ItalianoShop
Showing 1201–1230 of 1497 results
-
Current Probe Amplifiter
TEKTRONIX TCPA300
Current Probe Amplifier.
The TCPA300 from Tektronix is a current probe amplifier. This amplifier when used with TCP312A, TCP305A and TCP303 probes, provides a wide range of current measurement capability and spans the gap between low level milliamp measurements to very high current levels. These three probes provide current measurement capabilities of 30A, 50A and 150A DC continuous and for even higher current levels. Higher frequency performance is available with TCP312A providing greater than or equal to 100MHz bandwidth and maximum current of 30A DC. The TCPA300 is approved by UL3111-1 first edition, CAN/CSA C22.2 number 1010.1-92, EN61010-1:2001, EC Council Directive 89/336/EEC, FCC Part 15, Subpart B class A and AS/NZS 2064.1/2 standards.DC to 100MHz maximum bandwidth
Automatic control and onscreen scaling and units
AC/DC input coupling
Low insertion impedance reduces device under test loading
Split core construction allows easy circuit connection
Status indicators provide visual operating status and notification of potential error conditions
Low DC drift and noise allows improved low level current measurements
DatasheetSKU: n/a -
Power Sensor
AGILENT – Hp/Keysight 8487A
HP AGILENT KEYSIGHT 8487A POWER SENSOR 50 MHz to 50 GHz
The 8487A power sensor is designed for use with the 435A/B, 436A, 437A, 438A, 70100A, EPM series, EPM-P series, E1416A, N1911A, N1912A, N1913A, and N1914A power meters. The 8487A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 50 MHz to 50 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -30 dBm to +20 dBm)
• 50 ohm impedance
• 2.4 mm(m) connector
Scheda TecnicaSKU: n/a -
MOTOROLA STORNO CPQ7000 SINGLE UNIT RAPID RATE CHARGE–ELN1022A
The CQP7000 was introduced to the Storno model line-up in 1988. There were three basic models, no keypad, limited keypad with display and full keypad with display. Known as the CQP7000a, b and c they were the Storno branded versions of the Motorola MX1000, 2000 and 3000. A wide variety of specific models and options were available with up to 100 channels and transmit powers up to 6W VHF and 5W at UHF.
The Storno 7000 was constructed in three main parts, the radio housing and baseplate assembly which had all the front and side button actuators and contacts for the separate battery. The internals consisted of the front shield which carried the LCD display, speaker, keypad membrane, personality EEPROM and controller of the peripheral electronics (COPE). The front shield clipped over the frame assembly which housed the top panel controls, the main circuit board with controller of the radio electronics (CORE), and the plug-in RF modules.
The CQP7000 supported a wide range of tone signalling standards, channel scanning and user programmable memory features, enhanced by the eight character alphanumeric display. Special options included submersible, encrypted, intrinsically safe and Storno PhoneNet 2200 trunked system compatible versions..
DatasheetSKU: n/a -
Oscilloscope 2 channels
TEKTRONIX 2430
The 2430 is a 150 MHz, 2 channel digital oscilloscope from Tektronix. Measure voltage or current signals over time in an electronic circuit or component to display amplitude, frequency and rise times, etc. Applications include troubleshooting, production test, and design.
Additional Features:
Bandwidth: 150 MHz
2 Channels
Sample Rate: 100MS/s
Dual Timebase
2mV/div- 5V/div
Auto Setup, Auto Measure, Auto Pass/Fail, and Auto Sequencing.
SKU: n/a -
Tester DI Radiazone Di Campo Elettromagnetico
LUTRON EMF-823
Measuring Tesla Range x Accuracy: 20 micro Tesla x 0.01 micro Tesla, 200 micro Tesla x 0.1 micro Tesla, 2000 micro Tesla x 1 micro Tesla; Accuracy: ± (4 % + 3 d) – 20 micro Tesla, ± (5 % + 3 d) – 200 micro Tesla, ± (10 % + 5 d) – 2000 micro Tesla
Milli-Gauss Range x Resolution: 200 milli Gauss x 0.1 milli Gauss, 2000 milli Gauss x 1 milli Gauss, 20000 milli Gauss x 10 milli Gauss; Accuracy: 200 milli Gauss range, 2000 milli Gauss range, 20000 milli Gauss range.
Sampling Time: Approx. 0.4 second; Band width: 30 Hz to 300 Hz; Number of Axes: Single axis.
Operating Temperature: 0°C to 50 °C; Operating Humidity: Less than 80% RH
Accessories: Operation Manual, EMF MeteSKU: n/a -
Active Probe
TEKTRONIX TAP2500
TAP2500 is a single-ended active FET probe. It provides excellent high-speed electrical and mechanical performance required for today’s digital system designs. It is an easy access to oscilloscope probe menu display for probe status/diagnostic information and to control probe DC offset. It provides truer signal reproduction and fidelity for high-frequency measurements. It is specifically designed for use and direct connection to oscilloscopes with the TekVPI™ probe interface, the TAP2500 active FET probes achieve high-speed signal acquisition and measurement fidelity by solving three traditional problems they are lower DUT loading effects with ≤0.8pF input capacitance and 40kΩ input resistance, versatile DUT connectivity for attaching to small SMDs and preserves instrument bandwidth at the probe tip for up to 3.5GHz oscilloscopes.
High probe bandwidth
Fast probe rise time
Excellent signal fidelity
Small compact probe head for probing small geometry circuit elements
Robust design for reliability
Connects directly to oscilloscopes with the TekVPI™ probe interface
Provides automatic units scaling and readout on the oscilloscope display
Remote GPIB/USB probe control through the oscilloscope
DatasheetSKU: n/a -
Network Analyzer
HP-Agilent/Keysight 8757D CRT
The HP 8757D scalar network analyzer allows you to measure insertion loss, gain, return loss, SWR, and power quickly and accurately . With high-performance detectors and directional bridges, and a companion Keysight source and printer, this analyzer becomes the basis of a complete measurement system with superb performance.
Setup time is reduced by external disk save/recall, and measurement data can be sent directly to a printer while you proceed to the next measurement.
You can configure your system using a Keysight PSG signal generator with ramp sweep capability. The dynamic range can be extended from 75 dB to 83 dB using the PSG's high power option.
The Agilent 8757D has four independent display channels that process the signals from the Agilent 85037 series precision detectors, 85025 and 85026 detectors, and the 85027 series directional bridges for logarithmic display, in single channel or ratio mode. Three (optionally four) detector inputs are provided.
The number of points (horizontal resolution) that can be selected depends on the number of traces displayed.
A display is considered faulty if:
• A complete row or column of “stuck” or “dark” pixels.
• More than six “stuck on” pixels (but not more than three green) or more than 0.002% of the total pixels are within the LCD specifications.
• More than twelve “dark” pixels (but no more than seven of the same color) or more than 0.004% of the total pixels are within the LCD specifications.
• Two or more consecutive “stuck on” pixels or three or more consecutive “dark” pixel (but no more than one set of two consecutive dark pixels) “Stuck on” of “dark” pixels less than 6.5 mm apart (excluding consecutive pixels.All analyzer display channels can display any one of the detector inputs or any ratio combination of detector inputs.
Log magnitude >
dBm: single channel power measurement
dB: relative power measurement (ratio or relative to trace memory)SWR > Relative measurements (normalized or ratio measurements) can be displayed in SWR. Channels 1 and 2 only: 401 points or fewer
AUX voltage > The rear panel BNC input ADC IN can be measured and displayed in volts (–10 to +10 volts). Typical maximum error is 60 mV.
Up to 8 operator-selectable colors are available for LCD attributes, such as the grid, measurement traces, and labels.
The minimum sweep time depends on the number of traces displayed and the number of points selected.
Traces are stored and normalized with the highest resolution, independent of display scale/division or offset. With adaptive normalization on the Agilent 8757D, calibration data is interpolated when the frequency span is decreased.
Key Features & SpecificationsUp to 83 dB dynamic range
Buffered plotter/printer output
Built-in limit testing for quick pass/fail decisions
External disc and internal register save/recall of test setups
Color display
Optional internal power meter calibrator and precision detectors provide near power meter accuracy
DISLPAY CRT
Four display channels
Three detector inputs
+16 to –60 dBm dynamic range
AC/DC detection modes
101 to 1601 measurement points/trace
Compatible with the Agilent 85025 and 85026 series detectors and the Agilent 85027 series directional bridges
Limit line testing (channels 1 and 2)
Adaptive normalization
Cursor search functions (max, min, n dB, BW)SKU: 69
-
Current Probe Amplifiter
TEKTRONIX TCPA300
Current Probe Amplifier.
The TCPA300 from Tektronix is a current probe amplifier. This amplifier when used with TCP312A, TCP305A and TCP303 probes, provides a wide range of current measurement capability and spans the gap between low level milliamp measurements to very high current levels. These three probes provide current measurement capabilities of 30A, 50A and 150A DC continuous and for even higher current levels. Higher frequency performance is available with TCP312A providing greater than or equal to 100MHz bandwidth and maximum current of 30A DC. The TCPA300 is approved by UL3111-1 first edition, CAN/CSA C22.2 number 1010.1-92, EN61010-1:2001, EC Council Directive 89/336/EEC, FCC Part 15, Subpart B class A and AS/NZS 2064.1/2 standards.DC to 100MHz maximum bandwidth
Automatic control and onscreen scaling and units
AC/DC input coupling
Low insertion impedance reduces device under test loading
Split core construction allows easy circuit connection
Status indicators provide visual operating status and notification of potential error conditions
Low DC drift and noise allows improved low level current measurements
Datasheet -
Power Sensor
AGILENT – Hp/Keysight 8487A
HP AGILENT KEYSIGHT 8487A POWER SENSOR 50 MHz to 50 GHz
The 8487A power sensor is designed for use with the 435A/B, 436A, 437A, 438A, 70100A, EPM series, EPM-P series, E1416A, N1911A, N1912A, N1913A, and N1914A power meters. The 8487A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 50 MHz to 50 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -30 dBm to +20 dBm)
• 50 ohm impedance
• 2.4 mm(m) connector
Scheda Tecnica -
MOTOROLA STORNO CPQ7000 SINGLE UNIT RAPID RATE CHARGE–ELN1022A
The CQP7000 was introduced to the Storno model line-up in 1988. There were three basic models, no keypad, limited keypad with display and full keypad with display. Known as the CQP7000a, b and c they were the Storno branded versions of the Motorola MX1000, 2000 and 3000. A wide variety of specific models and options were available with up to 100 channels and transmit powers up to 6W VHF and 5W at UHF.
The Storno 7000 was constructed in three main parts, the radio housing and baseplate assembly which had all the front and side button actuators and contacts for the separate battery. The internals consisted of the front shield which carried the LCD display, speaker, keypad membrane, personality EEPROM and controller of the peripheral electronics (COPE). The front shield clipped over the frame assembly which housed the top panel controls, the main circuit board with controller of the radio electronics (CORE), and the plug-in RF modules.
The CQP7000 supported a wide range of tone signalling standards, channel scanning and user programmable memory features, enhanced by the eight character alphanumeric display. Special options included submersible, encrypted, intrinsically safe and Storno PhoneNet 2200 trunked system compatible versions..
Datasheet -
Oscilloscope 2 channels
TEKTRONIX 2430
The 2430 is a 150 MHz, 2 channel digital oscilloscope from Tektronix. Measure voltage or current signals over time in an electronic circuit or component to display amplitude, frequency and rise times, etc. Applications include troubleshooting, production test, and design.
Additional Features:
Bandwidth: 150 MHz
2 Channels
Sample Rate: 100MS/s
Dual Timebase
2mV/div- 5V/div
Auto Setup, Auto Measure, Auto Pass/Fail, and Auto Sequencing.
-
Tester DI Radiazone Di Campo Elettromagnetico
LUTRON EMF-823
Measuring Tesla Range x Accuracy: 20 micro Tesla x 0.01 micro Tesla, 200 micro Tesla x 0.1 micro Tesla, 2000 micro Tesla x 1 micro Tesla; Accuracy: ± (4 % + 3 d) – 20 micro Tesla, ± (5 % + 3 d) – 200 micro Tesla, ± (10 % + 5 d) – 2000 micro Tesla
Milli-Gauss Range x Resolution: 200 milli Gauss x 0.1 milli Gauss, 2000 milli Gauss x 1 milli Gauss, 20000 milli Gauss x 10 milli Gauss; Accuracy: 200 milli Gauss range, 2000 milli Gauss range, 20000 milli Gauss range.
Sampling Time: Approx. 0.4 second; Band width: 30 Hz to 300 Hz; Number of Axes: Single axis.
Operating Temperature: 0°C to 50 °C; Operating Humidity: Less than 80% RH
Accessories: Operation Manual, EMF Mete -
Active Probe
TEKTRONIX TAP2500
TAP2500 is a single-ended active FET probe. It provides excellent high-speed electrical and mechanical performance required for today’s digital system designs. It is an easy access to oscilloscope probe menu display for probe status/diagnostic information and to control probe DC offset. It provides truer signal reproduction and fidelity for high-frequency measurements. It is specifically designed for use and direct connection to oscilloscopes with the TekVPI™ probe interface, the TAP2500 active FET probes achieve high-speed signal acquisition and measurement fidelity by solving three traditional problems they are lower DUT loading effects with ≤0.8pF input capacitance and 40kΩ input resistance, versatile DUT connectivity for attaching to small SMDs and preserves instrument bandwidth at the probe tip for up to 3.5GHz oscilloscopes.
High probe bandwidth
Fast probe rise time
Excellent signal fidelity
Small compact probe head for probing small geometry circuit elements
Robust design for reliability
Connects directly to oscilloscopes with the TekVPI™ probe interface
Provides automatic units scaling and readout on the oscilloscope display
Remote GPIB/USB probe control through the oscilloscope
Datasheet -
Network Analyzer
HP-Agilent/Keysight 8757D CRT
The HP 8757D scalar network analyzer allows you to measure insertion loss, gain, return loss, SWR, and power quickly and accurately . With high-performance detectors and directional bridges, and a companion Keysight source and printer, this analyzer becomes the basis of a complete measurement system with superb performance.
Setup time is reduced by external disk save/recall, and measurement data can be sent directly to a printer while you proceed to the next measurement.
You can configure your system using a Keysight PSG signal generator with ramp sweep capability. The dynamic range can be extended from 75 dB to 83 dB using the PSG's high power option.
The Agilent 8757D has four independent display channels that process the signals from the Agilent 85037 series precision detectors, 85025 and 85026 detectors, and the 85027 series directional bridges for logarithmic display, in single channel or ratio mode. Three (optionally four) detector inputs are provided.
The number of points (horizontal resolution) that can be selected depends on the number of traces displayed.
A display is considered faulty if:
• A complete row or column of “stuck” or “dark” pixels.
• More than six “stuck on” pixels (but not more than three green) or more than 0.002% of the total pixels are within the LCD specifications.
• More than twelve “dark” pixels (but no more than seven of the same color) or more than 0.004% of the total pixels are within the LCD specifications.
• Two or more consecutive “stuck on” pixels or three or more consecutive “dark” pixel (but no more than one set of two consecutive dark pixels) “Stuck on” of “dark” pixels less than 6.5 mm apart (excluding consecutive pixels.All analyzer display channels can display any one of the detector inputs or any ratio combination of detector inputs.
Log magnitude >
dBm: single channel power measurement
dB: relative power measurement (ratio or relative to trace memory)SWR > Relative measurements (normalized or ratio measurements) can be displayed in SWR. Channels 1 and 2 only: 401 points or fewer
AUX voltage > The rear panel BNC input ADC IN can be measured and displayed in volts (–10 to +10 volts). Typical maximum error is 60 mV.
Up to 8 operator-selectable colors are available for LCD attributes, such as the grid, measurement traces, and labels.
The minimum sweep time depends on the number of traces displayed and the number of points selected.
Traces are stored and normalized with the highest resolution, independent of display scale/division or offset. With adaptive normalization on the Agilent 8757D, calibration data is interpolated when the frequency span is decreased.
Key Features & SpecificationsUp to 83 dB dynamic range
Buffered plotter/printer output
Built-in limit testing for quick pass/fail decisions
External disc and internal register save/recall of test setups
Color display
Optional internal power meter calibrator and precision detectors provide near power meter accuracy
DISLPAY CRT
Four display channels
Three detector inputs
+16 to –60 dBm dynamic range
AC/DC detection modes
101 to 1601 measurement points/trace
Compatible with the Agilent 85025 and 85026 series detectors and the Agilent 85027 series directional bridges
Limit line testing (channels 1 and 2)
Adaptive normalization
Cursor search functions (max, min, n dB, BW)
-
Current Probe Amplifiter
TEKTRONIX TCPA300
Current Probe Amplifier.
The TCPA300 from Tektronix is a current probe amplifier. This amplifier when used with TCP312A, TCP305A and TCP303 probes, provides a wide range of current measurement capability and spans the gap between low level milliamp measurements to very high current levels. These three probes provide current measurement capabilities of 30A, 50A and 150A DC continuous and for even higher current levels. Higher frequency performance is available with TCP312A providing greater than or equal to 100MHz bandwidth and maximum current of 30A DC. The TCPA300 is approved by UL3111-1 first edition, CAN/CSA C22.2 number 1010.1-92, EN61010-1:2001, EC Council Directive 89/336/EEC, FCC Part 15, Subpart B class A and AS/NZS 2064.1/2 standards.DC to 100MHz maximum bandwidth
Automatic control and onscreen scaling and units
AC/DC input coupling
Low insertion impedance reduces device under test loading
Split core construction allows easy circuit connection
Status indicators provide visual operating status and notification of potential error conditions
Low DC drift and noise allows improved low level current measurements
Datasheet -
Power Sensor
AGILENT – Hp/Keysight 8487A
HP AGILENT KEYSIGHT 8487A POWER SENSOR 50 MHz to 50 GHz
The 8487A power sensor is designed for use with the 435A/B, 436A, 437A, 438A, 70100A, EPM series, EPM-P series, E1416A, N1911A, N1912A, N1913A, and N1914A power meters. The 8487A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 50 MHz to 50 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -30 dBm to +20 dBm)
• 50 ohm impedance
• 2.4 mm(m) connector
Scheda Tecnica -
MOTOROLA STORNO CPQ7000 SINGLE UNIT RAPID RATE CHARGE–ELN1022A
The CQP7000 was introduced to the Storno model line-up in 1988. There were three basic models, no keypad, limited keypad with display and full keypad with display. Known as the CQP7000a, b and c they were the Storno branded versions of the Motorola MX1000, 2000 and 3000. A wide variety of specific models and options were available with up to 100 channels and transmit powers up to 6W VHF and 5W at UHF.
The Storno 7000 was constructed in three main parts, the radio housing and baseplate assembly which had all the front and side button actuators and contacts for the separate battery. The internals consisted of the front shield which carried the LCD display, speaker, keypad membrane, personality EEPROM and controller of the peripheral electronics (COPE). The front shield clipped over the frame assembly which housed the top panel controls, the main circuit board with controller of the radio electronics (CORE), and the plug-in RF modules.
The CQP7000 supported a wide range of tone signalling standards, channel scanning and user programmable memory features, enhanced by the eight character alphanumeric display. Special options included submersible, encrypted, intrinsically safe and Storno PhoneNet 2200 trunked system compatible versions..
Datasheet -
Oscilloscope 2 channels
TEKTRONIX 2430
The 2430 is a 150 MHz, 2 channel digital oscilloscope from Tektronix. Measure voltage or current signals over time in an electronic circuit or component to display amplitude, frequency and rise times, etc. Applications include troubleshooting, production test, and design.
Additional Features:
Bandwidth: 150 MHz
2 Channels
Sample Rate: 100MS/s
Dual Timebase
2mV/div- 5V/div
Auto Setup, Auto Measure, Auto Pass/Fail, and Auto Sequencing.
-
Tester DI Radiazone Di Campo Elettromagnetico
LUTRON EMF-823
Measuring Tesla Range x Accuracy: 20 micro Tesla x 0.01 micro Tesla, 200 micro Tesla x 0.1 micro Tesla, 2000 micro Tesla x 1 micro Tesla; Accuracy: ± (4 % + 3 d) – 20 micro Tesla, ± (5 % + 3 d) – 200 micro Tesla, ± (10 % + 5 d) – 2000 micro Tesla
Milli-Gauss Range x Resolution: 200 milli Gauss x 0.1 milli Gauss, 2000 milli Gauss x 1 milli Gauss, 20000 milli Gauss x 10 milli Gauss; Accuracy: 200 milli Gauss range, 2000 milli Gauss range, 20000 milli Gauss range.
Sampling Time: Approx. 0.4 second; Band width: 30 Hz to 300 Hz; Number of Axes: Single axis.
Operating Temperature: 0°C to 50 °C; Operating Humidity: Less than 80% RH
Accessories: Operation Manual, EMF Mete -
Active Probe
TEKTRONIX TAP2500
TAP2500 is a single-ended active FET probe. It provides excellent high-speed electrical and mechanical performance required for today’s digital system designs. It is an easy access to oscilloscope probe menu display for probe status/diagnostic information and to control probe DC offset. It provides truer signal reproduction and fidelity for high-frequency measurements. It is specifically designed for use and direct connection to oscilloscopes with the TekVPI™ probe interface, the TAP2500 active FET probes achieve high-speed signal acquisition and measurement fidelity by solving three traditional problems they are lower DUT loading effects with ≤0.8pF input capacitance and 40kΩ input resistance, versatile DUT connectivity for attaching to small SMDs and preserves instrument bandwidth at the probe tip for up to 3.5GHz oscilloscopes.
High probe bandwidth
Fast probe rise time
Excellent signal fidelity
Small compact probe head for probing small geometry circuit elements
Robust design for reliability
Connects directly to oscilloscopes with the TekVPI™ probe interface
Provides automatic units scaling and readout on the oscilloscope display
Remote GPIB/USB probe control through the oscilloscope
Datasheet -
Network Analyzer
HP-Agilent/Keysight 8757D CRT
The HP 8757D scalar network analyzer allows you to measure insertion loss, gain, return loss, SWR, and power quickly and accurately . With high-performance detectors and directional bridges, and a companion Keysight source and printer, this analyzer becomes the basis of a complete measurement system with superb performance.
Setup time is reduced by external disk save/recall, and measurement data can be sent directly to a printer while you proceed to the next measurement.
You can configure your system using a Keysight PSG signal generator with ramp sweep capability. The dynamic range can be extended from 75 dB to 83 dB using the PSG's high power option.
The Agilent 8757D has four independent display channels that process the signals from the Agilent 85037 series precision detectors, 85025 and 85026 detectors, and the 85027 series directional bridges for logarithmic display, in single channel or ratio mode. Three (optionally four) detector inputs are provided.
The number of points (horizontal resolution) that can be selected depends on the number of traces displayed.
A display is considered faulty if:
• A complete row or column of “stuck” or “dark” pixels.
• More than six “stuck on” pixels (but not more than three green) or more than 0.002% of the total pixels are within the LCD specifications.
• More than twelve “dark” pixels (but no more than seven of the same color) or more than 0.004% of the total pixels are within the LCD specifications.
• Two or more consecutive “stuck on” pixels or three or more consecutive “dark” pixel (but no more than one set of two consecutive dark pixels) “Stuck on” of “dark” pixels less than 6.5 mm apart (excluding consecutive pixels.All analyzer display channels can display any one of the detector inputs or any ratio combination of detector inputs.
Log magnitude >
dBm: single channel power measurement
dB: relative power measurement (ratio or relative to trace memory)SWR > Relative measurements (normalized or ratio measurements) can be displayed in SWR. Channels 1 and 2 only: 401 points or fewer
AUX voltage > The rear panel BNC input ADC IN can be measured and displayed in volts (–10 to +10 volts). Typical maximum error is 60 mV.
Up to 8 operator-selectable colors are available for LCD attributes, such as the grid, measurement traces, and labels.
The minimum sweep time depends on the number of traces displayed and the number of points selected.
Traces are stored and normalized with the highest resolution, independent of display scale/division or offset. With adaptive normalization on the Agilent 8757D, calibration data is interpolated when the frequency span is decreased.
Key Features & SpecificationsUp to 83 dB dynamic range
Buffered plotter/printer output
Built-in limit testing for quick pass/fail decisions
External disc and internal register save/recall of test setups
Color display
Optional internal power meter calibrator and precision detectors provide near power meter accuracy
DISLPAY CRT
Four display channels
Three detector inputs
+16 to –60 dBm dynamic range
AC/DC detection modes
101 to 1601 measurement points/trace
Compatible with the Agilent 85025 and 85026 series detectors and the Agilent 85027 series directional bridges
Limit line testing (channels 1 and 2)
Adaptive normalization
Cursor search functions (max, min, n dB, BW)