ItalianoHP-Agilent/Keysight
Showing 301–330 of 455 results
-
Power Supply
HP-Agilent/Keysight 6625A
Keysight high performance DC power supplies offer spec and accuracy for test optimization. The precision multiple output, 25W – 50W GPIB 6625A, 6626A, 6628A, and 6629A provide fast, low-noise outputs- dual-range, precision low current measurement- built-in measurements and advanced programmable features- and protection features to ensure DUT safety. * Low-range volts, amps 25W: 0 to 7 V, 0 to 15 mA. * Low-range volts, amps 50W: 0 to 16 V, 0 to 200 mA. * High range volts, amps 25W: 0 to 50 V, 0 to 500 mA. * High range volts, amps 50W: 0 to 50 V, 0 to 1 A or, 0 to 16 V, 0 to 2 A. * Voltage 25W: 0.016% + 1.5 mV (low), 10 mV (high). * Voltage 50W: 0.016% + 53 mV (low), 10 mV (high). * Current 25W: 0.04% + 15 µA (low), 100 µA (high). * Current 50W: 0.04% + 185 µA (low), 500 µA (high). * Voltage rms: 500 µV. * Peak-to-peak: 3 mV. * Current rms: 0.1 mA.
25W or 50W, 2 outputsSKU: 1160 -
Power Meter
HP/Agilent-Keysight E4419B
The E4419B power meter is designed for bench and automatic test equipment (ATE) use.
True dual-channel power meter – two simultaneous power readings
Fast measurement speed (up to 100 readings per second, over the GPIB, with E-series sensors)
Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
No range-switching delays with 8480 series sensors, and only one fast-range switching point with E-series sensors
Code compatibility with 438A power meter
GPIB and RS232 connector for remote control of all functionsSupplemental characteristics (shown in italics) are intended to provide additional information, useful in applying the instrument by giving typical (expected), but not warranted performance parameters. These characteristics are shown in italics or labeled as “typical”, “nominal” or “approximate”.
For information on measurement uncertainty calculations, refer to Application Note 64-1C, “Fundamentals of RF and Microwave Power Measurements”, literature number 5965-6380E.
Frequency range: 9 kHz to 110 GHz, sensor dependent
Power range: –70 dBm to +44 dBm (100 pW to 25 W), sensor dependent.
Power sensors: Compatible with all 8480 series and E-series sensors
Single sensor dynamic range: 90 dB maximum (E-series sensors), 50 dB maximum ( 8480 series sensors).
Display units: Absolute: Watts or dBm. Relative: Percent or dB.
Display resolution: Selectable resolution of 1.0, 0.1, 0.01, and 0.001 dB in Log mode, or 1 to 4 digits in linear mode.
Default resolution: 0.01 dB in log mode, 3 digits in linear mode.
DatasheetSKU: n/a -
Detector
HP-Agilent/Keysight 11664A
HP 11664A is a detector designed for operation with the 8757/8756/8755 scalar network analyzers. The detect the envelope of the 27.8 kHz modulated RF signal to be displayed on the scalar network analyzer.
Frequency Range: 10 MHz to 18 GHz
Range: +16 dBm to -60 dBm
Maximum input power: +20 dBm (100 mW)
Input impedance: 50 ohms
Connector: N(m)
DatasheetSKU: 80 -
GPIB INTERFACE MODULE
HP-Agilent/Keysight N2757A
AGILENT N2757A – GPIB INTERFACE MODULE N2757A is a GPIB interface module for fast data transfers. If you need fast data transfers, equip your 5462X oscilloscope with GPIB communication. Keysight offers the N2757A GPIB interface module to provide a GPIB port for your oscilloscope.
SKU: 1066 -
Power Sensor
HP-Agilent/Keysight R8486A
HP AGILENT KEYSIGHT R8486A Thermocouple Waveguide Power Sensor 26.5 GHz to 40 GHz
The R8486A power sensor is designed for use with the EPM series, EPM-P series, 70100A, E1416A, 435A/B, 436A, 437A, 438A series power meters. The R8486A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• 50 MHz calibration port
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 26.5 GHz to 40 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -10 dBm to +20 dBm)
• UG-599/U waveguide flange
DatasheetSKU: n/a
-
Power Supply
HP-Agilent/Keysight 6625A
Keysight high performance DC power supplies offer spec and accuracy for test optimization. The precision multiple output, 25W – 50W GPIB 6625A, 6626A, 6628A, and 6629A provide fast, low-noise outputs- dual-range, precision low current measurement- built-in measurements and advanced programmable features- and protection features to ensure DUT safety. * Low-range volts, amps 25W: 0 to 7 V, 0 to 15 mA. * Low-range volts, amps 50W: 0 to 16 V, 0 to 200 mA. * High range volts, amps 25W: 0 to 50 V, 0 to 500 mA. * High range volts, amps 50W: 0 to 50 V, 0 to 1 A or, 0 to 16 V, 0 to 2 A. * Voltage 25W: 0.016% + 1.5 mV (low), 10 mV (high). * Voltage 50W: 0.016% + 53 mV (low), 10 mV (high). * Current 25W: 0.04% + 15 µA (low), 100 µA (high). * Current 50W: 0.04% + 185 µA (low), 500 µA (high). * Voltage rms: 500 µV. * Peak-to-peak: 3 mV. * Current rms: 0.1 mA.
25W or 50W, 2 outputs -
Power Meter
HP/Agilent-Keysight E4419B
The E4419B power meter is designed for bench and automatic test equipment (ATE) use.
True dual-channel power meter – two simultaneous power readings
Fast measurement speed (up to 100 readings per second, over the GPIB, with E-series sensors)
Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
No range-switching delays with 8480 series sensors, and only one fast-range switching point with E-series sensors
Code compatibility with 438A power meter
GPIB and RS232 connector for remote control of all functionsSupplemental characteristics (shown in italics) are intended to provide additional information, useful in applying the instrument by giving typical (expected), but not warranted performance parameters. These characteristics are shown in italics or labeled as “typical”, “nominal” or “approximate”.
For information on measurement uncertainty calculations, refer to Application Note 64-1C, “Fundamentals of RF and Microwave Power Measurements”, literature number 5965-6380E.
Frequency range: 9 kHz to 110 GHz, sensor dependent
Power range: –70 dBm to +44 dBm (100 pW to 25 W), sensor dependent.
Power sensors: Compatible with all 8480 series and E-series sensors
Single sensor dynamic range: 90 dB maximum (E-series sensors), 50 dB maximum ( 8480 series sensors).
Display units: Absolute: Watts or dBm. Relative: Percent or dB.
Display resolution: Selectable resolution of 1.0, 0.1, 0.01, and 0.001 dB in Log mode, or 1 to 4 digits in linear mode.
Default resolution: 0.01 dB in log mode, 3 digits in linear mode.
Datasheet -
Detector
HP-Agilent/Keysight 11664A
HP 11664A is a detector designed for operation with the 8757/8756/8755 scalar network analyzers. The detect the envelope of the 27.8 kHz modulated RF signal to be displayed on the scalar network analyzer.
Frequency Range: 10 MHz to 18 GHz
Range: +16 dBm to -60 dBm
Maximum input power: +20 dBm (100 mW)
Input impedance: 50 ohms
Connector: N(m)
Datasheet -
GPIB INTERFACE MODULE
HP-Agilent/Keysight N2757A
AGILENT N2757A – GPIB INTERFACE MODULE N2757A is a GPIB interface module for fast data transfers. If you need fast data transfers, equip your 5462X oscilloscope with GPIB communication. Keysight offers the N2757A GPIB interface module to provide a GPIB port for your oscilloscope.
-
Power Sensor
HP-Agilent/Keysight R8486A
HP AGILENT KEYSIGHT R8486A Thermocouple Waveguide Power Sensor 26.5 GHz to 40 GHz
The R8486A power sensor is designed for use with the EPM series, EPM-P series, 70100A, E1416A, 435A/B, 436A, 437A, 438A series power meters. The R8486A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• 50 MHz calibration port
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 26.5 GHz to 40 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -10 dBm to +20 dBm)
• UG-599/U waveguide flange
Datasheet
-
Power Supply
HP-Agilent/Keysight 6625A
Keysight high performance DC power supplies offer spec and accuracy for test optimization. The precision multiple output, 25W – 50W GPIB 6625A, 6626A, 6628A, and 6629A provide fast, low-noise outputs- dual-range, precision low current measurement- built-in measurements and advanced programmable features- and protection features to ensure DUT safety. * Low-range volts, amps 25W: 0 to 7 V, 0 to 15 mA. * Low-range volts, amps 50W: 0 to 16 V, 0 to 200 mA. * High range volts, amps 25W: 0 to 50 V, 0 to 500 mA. * High range volts, amps 50W: 0 to 50 V, 0 to 1 A or, 0 to 16 V, 0 to 2 A. * Voltage 25W: 0.016% + 1.5 mV (low), 10 mV (high). * Voltage 50W: 0.016% + 53 mV (low), 10 mV (high). * Current 25W: 0.04% + 15 µA (low), 100 µA (high). * Current 50W: 0.04% + 185 µA (low), 500 µA (high). * Voltage rms: 500 µV. * Peak-to-peak: 3 mV. * Current rms: 0.1 mA.
25W or 50W, 2 outputs -
Power Meter
HP/Agilent-Keysight E4419B
The E4419B power meter is designed for bench and automatic test equipment (ATE) use.
True dual-channel power meter – two simultaneous power readings
Fast measurement speed (up to 100 readings per second, over the GPIB, with E-series sensors)
Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
No range-switching delays with 8480 series sensors, and only one fast-range switching point with E-series sensors
Code compatibility with 438A power meter
GPIB and RS232 connector for remote control of all functionsSupplemental characteristics (shown in italics) are intended to provide additional information, useful in applying the instrument by giving typical (expected), but not warranted performance parameters. These characteristics are shown in italics or labeled as “typical”, “nominal” or “approximate”.
For information on measurement uncertainty calculations, refer to Application Note 64-1C, “Fundamentals of RF and Microwave Power Measurements”, literature number 5965-6380E.
Frequency range: 9 kHz to 110 GHz, sensor dependent
Power range: –70 dBm to +44 dBm (100 pW to 25 W), sensor dependent.
Power sensors: Compatible with all 8480 series and E-series sensors
Single sensor dynamic range: 90 dB maximum (E-series sensors), 50 dB maximum ( 8480 series sensors).
Display units: Absolute: Watts or dBm. Relative: Percent or dB.
Display resolution: Selectable resolution of 1.0, 0.1, 0.01, and 0.001 dB in Log mode, or 1 to 4 digits in linear mode.
Default resolution: 0.01 dB in log mode, 3 digits in linear mode.
Datasheet -
Detector
HP-Agilent/Keysight 11664A
HP 11664A is a detector designed for operation with the 8757/8756/8755 scalar network analyzers. The detect the envelope of the 27.8 kHz modulated RF signal to be displayed on the scalar network analyzer.
Frequency Range: 10 MHz to 18 GHz
Range: +16 dBm to -60 dBm
Maximum input power: +20 dBm (100 mW)
Input impedance: 50 ohms
Connector: N(m)
Datasheet -
GPIB INTERFACE MODULE
HP-Agilent/Keysight N2757A
AGILENT N2757A – GPIB INTERFACE MODULE N2757A is a GPIB interface module for fast data transfers. If you need fast data transfers, equip your 5462X oscilloscope with GPIB communication. Keysight offers the N2757A GPIB interface module to provide a GPIB port for your oscilloscope.
-
Power Sensor
HP-Agilent/Keysight R8486A
HP AGILENT KEYSIGHT R8486A Thermocouple Waveguide Power Sensor 26.5 GHz to 40 GHz
The R8486A power sensor is designed for use with the EPM series, EPM-P series, 70100A, E1416A, 435A/B, 436A, 437A, 438A series power meters. The R8486A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• 50 MHz calibration port
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 26.5 GHz to 40 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -10 dBm to +20 dBm)
• UG-599/U waveguide flange
Datasheet