ItalianoHP-Agilent/Keysight
Showing 421–450 of 455 results
-
NOISE SOURCE
HP-Agilent/Keysight R347B
La sorgente di rumore Keysight R347B copre una gamma di frequenza da 26,5 a 40 GHz. Questa sorgente di rumore a guida d'onda consente di effettuare misurazioni accurate e convenienti della figura di rumore su dispositivi a onde millimetriche. L'R347B fornisce un rumore a banda larga ad alta precisione all'ingresso del sistema o del componente in prova. Il misuratore della figura di rumore elabora quindi il rapporto ON/OFF della potenza di rumore presente nel sistema IF e fornisce una lettura accurata della figura di rumore e del guadagno. La sorgente di rumore R347B ha una notevole stabilità ENR nel tempo, che consente cicli di ricalibrazione più lunghi e misurazioni della figura di rumore più accurate. Prestazioni e affidabilità a frequenze millimetriche Eccellente stabilità ENR nel tempo Basso ROS
SKU: n/a -
Power Sensor
HP-Agilent/Keysight R8486A
HP AGILENT KEYSIGHT R8486A Thermocouple Waveguide Power Sensor 26.5 GHz to 40 GHz
The R8486A power sensor is designed for use with the EPM series, EPM-P series, 70100A, E1416A, 435A/B, 436A, 437A, 438A series power meters. The R8486A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• 50 MHz calibration port
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 26.5 GHz to 40 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -10 dBm to +20 dBm)
• UG-599/U waveguide flange
DatasheetSKU: n/a -
Power Sensor
HP-Agilent/Keysight R8486D
The R8486D diode waveguide power sensor measures average power over the frequency range 26.5 GHz to 40 GHz and power range -70 to -20 dBm (50 dB dynamic range).
Excellent SWR for reducing mismatch uncertainty
50 MHz calibration port
Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
Accurate average power measurements over -70 to -20 dBm
Frequency range 26.5 GHz to 40 GHz
Diode power sensing elementThe Keysight 11708A 30 dB attenuator is supplied with 8480 series power sensors with the “D” suffix, for calibration with the power meter 0 dBm, 50 MHz reference.
DatasheetSKU: n/a -
Waveguide Variable Attenuator
HP-Agilent/Keysight X382A
The attenuation value of this direct-reading, precision attenuator depends on the rotation angle of the resistive card, rather than on the resistivity value of the attenuating material. Therefore, it is insensitive to changes in temperature and humidity which can affect the resistive card of ordinary adjustable flap attenuators. The attenuation value is highly accurate and is stable from 0 to 50 dB. The instrument features large, easy-to-read dials, and can handle considerable microwave power. – Frequency range: 8.2 to 12.4 GHz. – Maximum SWR: 1.15. – Attenuation accuracy: ± 0.2% or 0.1 dB (whichever is greater). – Attenuation range: 0 to 50 dB. – Maximum power (CW): 10 Watts. – Waveguide designator: EIA WR-90 MIL-W-85/1-077. -Flange designator: UG-135/U MIL-F-3922/54C-008.
8.2 to 12.4 GHzSKU: 1204 -
Plug-in
HP/Agilent-Keysight 83570A
The HP 83570A RF plug-in provides a 18 MHz to 26.5 GHz.
Power is internally leveled to a flatness < ± 1.4 dB.
The output power has a calibrated range of 11 dB (7 dB for HP 83572A).
The power level may be manually set to a 0.1 dB resolution, or the power level may be remotely HP-IB programmed to a 0.01 dB resolution.
In addition to a single output power, these plug-ins also have a power sweep function.FMI 20093-KF20 Adaptor
HP OSCILLATOR
HP DOUBLER 5086-7300SKU: n/a -
Plug-in
HP/Agilent-Keysight 83592C
The HP 83592C RF plug-in provides a 10 MHz to 20 GHz broadband coaxial swept frequency source for the Keysight 8350B sweep oscillator mainframe. Applications include scalar network analysis, serving as a local oscillator for down-converting high frequency signals, and a stand-alone RF signal source.
High output power
Excellent harmonic performance
Low cost of ownership
HP FILTER
HP MULTIPLIER
HP OSCILLATOR
DatasheetSKU: n/a -
Network Analyzer
HP/Agilent-Keysight 8753ES
Agilent 8753ES vector network analyzers perform complete characterization of RF components.
30 kHz to 3 GHz
Frequency and power sweepsSpecifications describe the instrument’s warranted performance after a half-hour warm-up and over the temperature range of 25° ± 5° C, unless otherwise stated. Specifications for frequencies above 3 GHz do not apply to instruments with Option 075 (75-ohm impedance). Supplemental characteristics are typical but nonwarranted performance parameters. These are denoted as “typical,” “nominal,” or “approximate.” The measurement uncertainty curves and measurement port characteristics given for Agilent Technologies 8753ES systems also apply to the 8753ES with Options 006 and 011 and the 85047A test set (50-ohm), or the 8753ES Option 011 with an 85046B test set (75-ohm).
System dynamic range is calculated as the difference between the receiver noise floor and the lesser of either the source maximum output or the receiver maximum input level. System dynamic range applies to transmission measurements only, since reflection measurements are limited by directivity. Noise floor is specified as the mean of the noise trace over frequency. Noise floor is measured with the test ports terminated in loads, full two-port error correction for the 8753ES and enhancedresponse error correction for the 8753ET (with 16 averages used during isolation), 10 Hz IF bandwidth (BW), maximum test port power, and no averaging during the measurement.
Measurement uncertainty curves utilize a Root Sum Square (RSS) model for the contribution of random errors such as noise, typical connector repeatabilities, and test set switching; this is combined with a worst-case model for the contributions of dynamic accuracy and residual systematic errors. Curves show the worst-case magnitude and phase uncertainty for reflection and transmission measurements, after a full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET (including isolation with an averaging factor of 16) using the specified cal kit, with 10 Hz IF bandwidth (BW) and no averaging.
Characteristics show the residual system uncertainties for uncorrected performance and after accuracy enhancement using full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET. These characteristics apply for an environmental temperature of 25° ± 5° C, with less than 1° C deviation from the calibration temperature. Agilent 8753ET Option 004 may degrade transmission source match as much as 2 dB, resulting in up to 0.05 dB additional uncertainty in transmission tracking. Corrected performance indicates residual error after calibration. It is determined by the quality of calibration standards, system repeatability, stability, and noise. Uncorrected performance indicates intrinsic errors without calibration correction applied. This is related to the ultimate stability of a calibration.
DatasheetSKU: n/a -
Power Meter
HP/Agilent-Keysight E4419B
The E4419B power meter is designed for bench and automatic test equipment (ATE) use.
True dual-channel power meter – two simultaneous power readings
Fast measurement speed (up to 100 readings per second, over the GPIB, with E-series sensors)
Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
No range-switching delays with 8480 series sensors, and only one fast-range switching point with E-series sensors
Code compatibility with 438A power meter
GPIB and RS232 connector for remote control of all functionsSupplemental characteristics (shown in italics) are intended to provide additional information, useful in applying the instrument by giving typical (expected), but not warranted performance parameters. These characteristics are shown in italics or labeled as “typical”, “nominal” or “approximate”.
For information on measurement uncertainty calculations, refer to Application Note 64-1C, “Fundamentals of RF and Microwave Power Measurements”, literature number 5965-6380E.
Frequency range: 9 kHz to 110 GHz, sensor dependent
Power range: –70 dBm to +44 dBm (100 pW to 25 W), sensor dependent.
Power sensors: Compatible with all 8480 series and E-series sensors
Single sensor dynamic range: 90 dB maximum (E-series sensors), 50 dB maximum ( 8480 series sensors).
Display units: Absolute: Watts or dBm. Relative: Percent or dB.
Display resolution: Selectable resolution of 1.0, 0.1, 0.01, and 0.001 dB in Log mode, or 1 to 4 digits in linear mode.
Default resolution: 0.01 dB in log mode, 3 digits in linear mode.
DatasheetSKU: n/a
-
NOISE SOURCE
HP-Agilent/Keysight R347B
La sorgente di rumore Keysight R347B copre una gamma di frequenza da 26,5 a 40 GHz. Questa sorgente di rumore a guida d'onda consente di effettuare misurazioni accurate e convenienti della figura di rumore su dispositivi a onde millimetriche. L'R347B fornisce un rumore a banda larga ad alta precisione all'ingresso del sistema o del componente in prova. Il misuratore della figura di rumore elabora quindi il rapporto ON/OFF della potenza di rumore presente nel sistema IF e fornisce una lettura accurata della figura di rumore e del guadagno. La sorgente di rumore R347B ha una notevole stabilità ENR nel tempo, che consente cicli di ricalibrazione più lunghi e misurazioni della figura di rumore più accurate. Prestazioni e affidabilità a frequenze millimetriche Eccellente stabilità ENR nel tempo Basso ROS
-
Power Sensor
HP-Agilent/Keysight R8486A
HP AGILENT KEYSIGHT R8486A Thermocouple Waveguide Power Sensor 26.5 GHz to 40 GHz
The R8486A power sensor is designed for use with the EPM series, EPM-P series, 70100A, E1416A, 435A/B, 436A, 437A, 438A series power meters. The R8486A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• 50 MHz calibration port
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 26.5 GHz to 40 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -10 dBm to +20 dBm)
• UG-599/U waveguide flange
Datasheet -
Power Sensor
HP-Agilent/Keysight R8486D
The R8486D diode waveguide power sensor measures average power over the frequency range 26.5 GHz to 40 GHz and power range -70 to -20 dBm (50 dB dynamic range).
Excellent SWR for reducing mismatch uncertainty
50 MHz calibration port
Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
Accurate average power measurements over -70 to -20 dBm
Frequency range 26.5 GHz to 40 GHz
Diode power sensing elementThe Keysight 11708A 30 dB attenuator is supplied with 8480 series power sensors with the “D” suffix, for calibration with the power meter 0 dBm, 50 MHz reference.
Datasheet -
Waveguide Variable Attenuator
HP-Agilent/Keysight X382A
The attenuation value of this direct-reading, precision attenuator depends on the rotation angle of the resistive card, rather than on the resistivity value of the attenuating material. Therefore, it is insensitive to changes in temperature and humidity which can affect the resistive card of ordinary adjustable flap attenuators. The attenuation value is highly accurate and is stable from 0 to 50 dB. The instrument features large, easy-to-read dials, and can handle considerable microwave power. – Frequency range: 8.2 to 12.4 GHz. – Maximum SWR: 1.15. – Attenuation accuracy: ± 0.2% or 0.1 dB (whichever is greater). – Attenuation range: 0 to 50 dB. – Maximum power (CW): 10 Watts. – Waveguide designator: EIA WR-90 MIL-W-85/1-077. -Flange designator: UG-135/U MIL-F-3922/54C-008.
8.2 to 12.4 GHz -
Plug-in
HP/Agilent-Keysight 83570A
The HP 83570A RF plug-in provides a 18 MHz to 26.5 GHz.
Power is internally leveled to a flatness < ± 1.4 dB.
The output power has a calibrated range of 11 dB (7 dB for HP 83572A).
The power level may be manually set to a 0.1 dB resolution, or the power level may be remotely HP-IB programmed to a 0.01 dB resolution.
In addition to a single output power, these plug-ins also have a power sweep function.FMI 20093-KF20 Adaptor
HP OSCILLATOR
HP DOUBLER 5086-7300 -
Plug-in
HP/Agilent-Keysight 83592C
The HP 83592C RF plug-in provides a 10 MHz to 20 GHz broadband coaxial swept frequency source for the Keysight 8350B sweep oscillator mainframe. Applications include scalar network analysis, serving as a local oscillator for down-converting high frequency signals, and a stand-alone RF signal source.
High output power
Excellent harmonic performance
Low cost of ownership
HP FILTER
HP MULTIPLIER
HP OSCILLATOR
Datasheet -
Network Analyzer
HP/Agilent-Keysight 8753ES
Agilent 8753ES vector network analyzers perform complete characterization of RF components.
30 kHz to 3 GHz
Frequency and power sweepsSpecifications describe the instrument’s warranted performance after a half-hour warm-up and over the temperature range of 25° ± 5° C, unless otherwise stated. Specifications for frequencies above 3 GHz do not apply to instruments with Option 075 (75-ohm impedance). Supplemental characteristics are typical but nonwarranted performance parameters. These are denoted as “typical,” “nominal,” or “approximate.” The measurement uncertainty curves and measurement port characteristics given for Agilent Technologies 8753ES systems also apply to the 8753ES with Options 006 and 011 and the 85047A test set (50-ohm), or the 8753ES Option 011 with an 85046B test set (75-ohm).
System dynamic range is calculated as the difference between the receiver noise floor and the lesser of either the source maximum output or the receiver maximum input level. System dynamic range applies to transmission measurements only, since reflection measurements are limited by directivity. Noise floor is specified as the mean of the noise trace over frequency. Noise floor is measured with the test ports terminated in loads, full two-port error correction for the 8753ES and enhancedresponse error correction for the 8753ET (with 16 averages used during isolation), 10 Hz IF bandwidth (BW), maximum test port power, and no averaging during the measurement.
Measurement uncertainty curves utilize a Root Sum Square (RSS) model for the contribution of random errors such as noise, typical connector repeatabilities, and test set switching; this is combined with a worst-case model for the contributions of dynamic accuracy and residual systematic errors. Curves show the worst-case magnitude and phase uncertainty for reflection and transmission measurements, after a full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET (including isolation with an averaging factor of 16) using the specified cal kit, with 10 Hz IF bandwidth (BW) and no averaging.
Characteristics show the residual system uncertainties for uncorrected performance and after accuracy enhancement using full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET. These characteristics apply for an environmental temperature of 25° ± 5° C, with less than 1° C deviation from the calibration temperature. Agilent 8753ET Option 004 may degrade transmission source match as much as 2 dB, resulting in up to 0.05 dB additional uncertainty in transmission tracking. Corrected performance indicates residual error after calibration. It is determined by the quality of calibration standards, system repeatability, stability, and noise. Uncorrected performance indicates intrinsic errors without calibration correction applied. This is related to the ultimate stability of a calibration.
Datasheet -
Power Meter
HP/Agilent-Keysight E4419B
The E4419B power meter is designed for bench and automatic test equipment (ATE) use.
True dual-channel power meter – two simultaneous power readings
Fast measurement speed (up to 100 readings per second, over the GPIB, with E-series sensors)
Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
No range-switching delays with 8480 series sensors, and only one fast-range switching point with E-series sensors
Code compatibility with 438A power meter
GPIB and RS232 connector for remote control of all functionsSupplemental characteristics (shown in italics) are intended to provide additional information, useful in applying the instrument by giving typical (expected), but not warranted performance parameters. These characteristics are shown in italics or labeled as “typical”, “nominal” or “approximate”.
For information on measurement uncertainty calculations, refer to Application Note 64-1C, “Fundamentals of RF and Microwave Power Measurements”, literature number 5965-6380E.
Frequency range: 9 kHz to 110 GHz, sensor dependent
Power range: –70 dBm to +44 dBm (100 pW to 25 W), sensor dependent.
Power sensors: Compatible with all 8480 series and E-series sensors
Single sensor dynamic range: 90 dB maximum (E-series sensors), 50 dB maximum ( 8480 series sensors).
Display units: Absolute: Watts or dBm. Relative: Percent or dB.
Display resolution: Selectable resolution of 1.0, 0.1, 0.01, and 0.001 dB in Log mode, or 1 to 4 digits in linear mode.
Default resolution: 0.01 dB in log mode, 3 digits in linear mode.
Datasheet
-
NOISE SOURCE
HP-Agilent/Keysight R347B
La sorgente di rumore Keysight R347B copre una gamma di frequenza da 26,5 a 40 GHz. Questa sorgente di rumore a guida d'onda consente di effettuare misurazioni accurate e convenienti della figura di rumore su dispositivi a onde millimetriche. L'R347B fornisce un rumore a banda larga ad alta precisione all'ingresso del sistema o del componente in prova. Il misuratore della figura di rumore elabora quindi il rapporto ON/OFF della potenza di rumore presente nel sistema IF e fornisce una lettura accurata della figura di rumore e del guadagno. La sorgente di rumore R347B ha una notevole stabilità ENR nel tempo, che consente cicli di ricalibrazione più lunghi e misurazioni della figura di rumore più accurate. Prestazioni e affidabilità a frequenze millimetriche Eccellente stabilità ENR nel tempo Basso ROS
-
Power Sensor
HP-Agilent/Keysight R8486A
HP AGILENT KEYSIGHT R8486A Thermocouple Waveguide Power Sensor 26.5 GHz to 40 GHz
The R8486A power sensor is designed for use with the EPM series, EPM-P series, 70100A, E1416A, 435A/B, 436A, 437A, 438A series power meters. The R8486A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• 50 MHz calibration port
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 26.5 GHz to 40 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -10 dBm to +20 dBm)
• UG-599/U waveguide flange
Datasheet -
Power Sensor
HP-Agilent/Keysight R8486D
The R8486D diode waveguide power sensor measures average power over the frequency range 26.5 GHz to 40 GHz and power range -70 to -20 dBm (50 dB dynamic range).
Excellent SWR for reducing mismatch uncertainty
50 MHz calibration port
Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration
Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
Accurate average power measurements over -70 to -20 dBm
Frequency range 26.5 GHz to 40 GHz
Diode power sensing elementThe Keysight 11708A 30 dB attenuator is supplied with 8480 series power sensors with the “D” suffix, for calibration with the power meter 0 dBm, 50 MHz reference.
Datasheet -
Waveguide Variable Attenuator
HP-Agilent/Keysight X382A
The attenuation value of this direct-reading, precision attenuator depends on the rotation angle of the resistive card, rather than on the resistivity value of the attenuating material. Therefore, it is insensitive to changes in temperature and humidity which can affect the resistive card of ordinary adjustable flap attenuators. The attenuation value is highly accurate and is stable from 0 to 50 dB. The instrument features large, easy-to-read dials, and can handle considerable microwave power. – Frequency range: 8.2 to 12.4 GHz. – Maximum SWR: 1.15. – Attenuation accuracy: ± 0.2% or 0.1 dB (whichever is greater). – Attenuation range: 0 to 50 dB. – Maximum power (CW): 10 Watts. – Waveguide designator: EIA WR-90 MIL-W-85/1-077. -Flange designator: UG-135/U MIL-F-3922/54C-008.
8.2 to 12.4 GHz -
Plug-in
HP/Agilent-Keysight 83570A
The HP 83570A RF plug-in provides a 18 MHz to 26.5 GHz.
Power is internally leveled to a flatness < ± 1.4 dB.
The output power has a calibrated range of 11 dB (7 dB for HP 83572A).
The power level may be manually set to a 0.1 dB resolution, or the power level may be remotely HP-IB programmed to a 0.01 dB resolution.
In addition to a single output power, these plug-ins also have a power sweep function.FMI 20093-KF20 Adaptor
HP OSCILLATOR
HP DOUBLER 5086-7300 -
Plug-in
HP/Agilent-Keysight 83592C
The HP 83592C RF plug-in provides a 10 MHz to 20 GHz broadband coaxial swept frequency source for the Keysight 8350B sweep oscillator mainframe. Applications include scalar network analysis, serving as a local oscillator for down-converting high frequency signals, and a stand-alone RF signal source.
High output power
Excellent harmonic performance
Low cost of ownership
HP FILTER
HP MULTIPLIER
HP OSCILLATOR
Datasheet -
Network Analyzer
HP/Agilent-Keysight 8753ES
Agilent 8753ES vector network analyzers perform complete characterization of RF components.
30 kHz to 3 GHz
Frequency and power sweepsSpecifications describe the instrument’s warranted performance after a half-hour warm-up and over the temperature range of 25° ± 5° C, unless otherwise stated. Specifications for frequencies above 3 GHz do not apply to instruments with Option 075 (75-ohm impedance). Supplemental characteristics are typical but nonwarranted performance parameters. These are denoted as “typical,” “nominal,” or “approximate.” The measurement uncertainty curves and measurement port characteristics given for Agilent Technologies 8753ES systems also apply to the 8753ES with Options 006 and 011 and the 85047A test set (50-ohm), or the 8753ES Option 011 with an 85046B test set (75-ohm).
System dynamic range is calculated as the difference between the receiver noise floor and the lesser of either the source maximum output or the receiver maximum input level. System dynamic range applies to transmission measurements only, since reflection measurements are limited by directivity. Noise floor is specified as the mean of the noise trace over frequency. Noise floor is measured with the test ports terminated in loads, full two-port error correction for the 8753ES and enhancedresponse error correction for the 8753ET (with 16 averages used during isolation), 10 Hz IF bandwidth (BW), maximum test port power, and no averaging during the measurement.
Measurement uncertainty curves utilize a Root Sum Square (RSS) model for the contribution of random errors such as noise, typical connector repeatabilities, and test set switching; this is combined with a worst-case model for the contributions of dynamic accuracy and residual systematic errors. Curves show the worst-case magnitude and phase uncertainty for reflection and transmission measurements, after a full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET (including isolation with an averaging factor of 16) using the specified cal kit, with 10 Hz IF bandwidth (BW) and no averaging.
Characteristics show the residual system uncertainties for uncorrected performance and after accuracy enhancement using full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET. These characteristics apply for an environmental temperature of 25° ± 5° C, with less than 1° C deviation from the calibration temperature. Agilent 8753ET Option 004 may degrade transmission source match as much as 2 dB, resulting in up to 0.05 dB additional uncertainty in transmission tracking. Corrected performance indicates residual error after calibration. It is determined by the quality of calibration standards, system repeatability, stability, and noise. Uncorrected performance indicates intrinsic errors without calibration correction applied. This is related to the ultimate stability of a calibration.
Datasheet -
Power Meter
HP/Agilent-Keysight E4419B
The E4419B power meter is designed for bench and automatic test equipment (ATE) use.
True dual-channel power meter – two simultaneous power readings
Fast measurement speed (up to 100 readings per second, over the GPIB, with E-series sensors)
Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
No range-switching delays with 8480 series sensors, and only one fast-range switching point with E-series sensors
Code compatibility with 438A power meter
GPIB and RS232 connector for remote control of all functionsSupplemental characteristics (shown in italics) are intended to provide additional information, useful in applying the instrument by giving typical (expected), but not warranted performance parameters. These characteristics are shown in italics or labeled as “typical”, “nominal” or “approximate”.
For information on measurement uncertainty calculations, refer to Application Note 64-1C, “Fundamentals of RF and Microwave Power Measurements”, literature number 5965-6380E.
Frequency range: 9 kHz to 110 GHz, sensor dependent
Power range: –70 dBm to +44 dBm (100 pW to 25 W), sensor dependent.
Power sensors: Compatible with all 8480 series and E-series sensors
Single sensor dynamic range: 90 dB maximum (E-series sensors), 50 dB maximum ( 8480 series sensors).
Display units: Absolute: Watts or dBm. Relative: Percent or dB.
Display resolution: Selectable resolution of 1.0, 0.1, 0.01, and 0.001 dB in Log mode, or 1 to 4 digits in linear mode.
Default resolution: 0.01 dB in log mode, 3 digits in linear mode.
Datasheet