ItalianoShop
Showing 601–630 of 1386 results
-
Power Supply
HP E3616A 60W Power Supply, 35V, 1.7A
Keysight basic DC power supplies offer essential features for a tight budget.
The single output, 30-60 W, E3610A-E3617A provide small, compact size for bench use; low-noise and excellent regulation; and dual-range outputs (E3610A/11A/12A).
The Keysight 60W, single output E3616A is a reliable and convenient power for benchtop use, and offers solid performance and a variety of basic and enhanced capabilities.Output Ratings (Maximum current is derated 1% per °C between 40° to 55°C)
> Range 1: 0 to 35 V, 0 to 1.7 A
> Range 2: NA
> Power (max): 60 WRipple & Noise from 20 Hz to 20 MHz
> Voltage rms: 200 µV
> Peak-to-Peak: 1 mVLoad & Line Regulation
> 0.01% + 2 mVMeter Resolution
> Voltage: 10 mV (0-20 V), 100 mV (>20 V)
> Current: 1 mASKU: n/a -
PEAK POWER SENSOR
HP 8991A Peak Power Meter
The HP 8991A peak power analyzer provides complete and accurate characterization of today's complex pulsed signals. It is capable of performing seven automatic timing measurements (rise time, fall time, pulse width, PRI, PRF, duty cycle, and delay) and five automatic power measurement (peak power, average power, pulse top/base amplitude, and overshoot) with push-button ease. Front-panel operation is intuitive and straightforward. Data entries can be typed in or made with the front panel knob; automatic measurements are made with simple keystroke. The 8990A offers two sensor channels plus two external triggering/oscilloscope channels, allowing the simultaneous measurement of modulating signals and detector power envelopes.
* Amplitude and time markers for measuring power exactly where its needed
* Two oscilloscope channels for measuring time delay between video and microwave pulse
* Versatile triggering enables the capturing of exclusive glitches
* Waveform math functions for measuring scalar pulse parameters
* Dynamic Range: >45 dB
* Minimum Pulse Width: 20 ns
* Rise Time: <5 ns * Sensor and Video Inputs: 1 and 4; 2 and 3SKU: n/a -
Pulse Pattern Generator
TEKTRONIX PG 501
PULSE GENERATOR.
The PG501 provides simultaneous positive and negative 50 MHz output pulses with 5 ns rise and fall times and independently variable amplitudes from 0.5 V to 5 V into 50 Ω.
Front panel controls provide calibrated decade selection of pulse period from 20 ns to 20 ms, and duration from 10 ns to 10 ms. Uncalibrated pulse period from 20 ns to 0.2 s and duration from 10 ns to 0.1 s can be obtained with the variable control.
The PG501 has a gate input and a 10 ns pre-trigger output.SKU: n/a -
RF Impedance/Material Analyzer
HP-Agilent/Keysight 4291B
Four component test fixtures (DUT size: 0.5 mm to 20 mm)
Independent parameter selection in 2 channels
Direct read-out permittivity, permeability (option)
Two material fixtures (operating temperature: -55deg C to + 200deg C)
Versatile analysis (temperature, cole-cole plot, relaxation time)
Sweep parameters (frequency, ac level, dc bias, temperature)The Keysight 4291B RF impedance / material analyzer provides a total solution for high-accuracy and easy measurement of surface-mount components and dielectric / magnetic materials. The Keysight 4291B uses a direct current-voltage measurement technique, opposing the reflection measurement technique, for more accurate impedance measurement over wide impedance range.
Basic impedance accuracy is +/- 0.8%. High Q accuracy enables low-loss component analysis. An internal synthesizer sweeps frequency from 1 MHz to 1.8 GHz with 1 mHz resolution. A 1.8-m error-less cable connects the analyzer to a test station so you can extend your test point away from the analyzer without losing accuracy. Advanced calibration and error compensation function eliminate measurement error factors in fixtures and assure high accuracy and repeatability at DUT / MUT.
The Hp 4291B also provides automatic level control and monitor of test signals by using IBASIC programming function; devices can be measured under a constant voltage or current. Measure bias dependent impedance characteristics with optional dc bias (up to 40 V and 100 mA). At the push of a button, the built-in Equivalent Circuit Analysis Function automatically calculates the circuit constant values of five circuit models.
The Hp 4291B has two measurement channels; each channel can be set to measure a single (e.g. Z) or dual (e.g. Z-theta) impedance parameter. The color TFT with split-display can show both active traces and memory traces (stored in RAM). A built-in floppy disk drive stores programs and test data in either LIF or MS-DOS format. With built-in IBASIC, you can control external test equipment such as a temperature chamber or wafer prober directly from the Keysight 4291B. You do not need a separate instrument controller.
Material Evaluation
The Hp 4291B enables easy and sophisticated material evaluation and improves material evaluation quality and efficiency. The Hp 4291B provides the total dielectric / magnetic material measurement solutions in wide frequency range (1 MHz to 1 GHz).
DatasheetSKU: n/a -
Power Meter
ROHDE & SCHWARZ NRVS
Uncompromizing technology and
ease of operation make the NRVS an
ideal instrument for any kind of power
measurement in manifold laboratory
and system applications. Thanks to its
unique measuring heads with calibra-
tion data memory and temperature
sensor, which make adjustments by
the user superfluous, the NRVS meas-
ures at all times with high accuracy
and free of operator’s errors.
The range of measuring heads includes thermal power sensors as well as highly sensitive diode power sensors, peak power
sensors, probes and insertion units for voltage measurements. The NRVS covers a power span from 100 pW up to the
kW range. In addition to the power sensors, all voltage probes of the URV5-Z series can be used.
DatasheetSKU: n/a -
Cable
HP-Agilent/Keysight 11730A Sensore di potenza / Cavo sorgente rumore SNS (1,5 m / 5 piedi)
The Keysight 11730A/B/C/D/E cables are used with the N8480/8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements. The Keysight 11730A/B/C can also be used in conjunction with the SNS series noise sources which are designed to operate with the NFA Series Noise Figure Analyzers
SKU: 336€0.00 View Product -
Oscilloscope 2 channels
Rigol MSO4012
100MHz, 2 channel, 4GS/s
MSO4000 Series is the new mainstream digital scope to meet the customer’s applications with its innovative technology, industry leading specifications, powerful trigger functions and broad analysis capabilities. – Bandwidth 100MHz – Sample Rate Analog channel up to 4 GSa/s, Digital Channel up to 1 GSa/s(MSO) – Standard Memory depth: Analog channel up to 140 Mpts, Digital Channel up to 28 Mpts(MSO) – 2 Analog Channels, 16 Digital channels(MSO) – Waveform capture rate Up to 110,000 waveforms per second, – Real Time Waveform Record, Replay & Analysis(Std. up to 200,000 frames) – Lower noise floor, the Min. vertical sensitivity is 1mV/div – Innovative “UltraVision” technology – A variety of Trigger functions – Support serial bus trigger(Std.) and decoding(Opt.) for both analog and digital channels – Complete Connectivity: USB Host& Device, LAN(LXI-C), VGA, AUX,USB-GPIB(Opt.) – 9 inch WVGA(800X480), 256 level intensity grading displaySKU: 733
-
Power Supply
HP E3616A 60W Power Supply, 35V, 1.7A
Keysight basic DC power supplies offer essential features for a tight budget.
The single output, 30-60 W, E3610A-E3617A provide small, compact size for bench use; low-noise and excellent regulation; and dual-range outputs (E3610A/11A/12A).
The Keysight 60W, single output E3616A is a reliable and convenient power for benchtop use, and offers solid performance and a variety of basic and enhanced capabilities.Output Ratings (Maximum current is derated 1% per °C between 40° to 55°C)
> Range 1: 0 to 35 V, 0 to 1.7 A
> Range 2: NA
> Power (max): 60 WRipple & Noise from 20 Hz to 20 MHz
> Voltage rms: 200 µV
> Peak-to-Peak: 1 mVLoad & Line Regulation
> 0.01% + 2 mVMeter Resolution
> Voltage: 10 mV (0-20 V), 100 mV (>20 V)
> Current: 1 mA -
PEAK POWER SENSOR
HP 8991A Peak Power Meter
The HP 8991A peak power analyzer provides complete and accurate characterization of today's complex pulsed signals. It is capable of performing seven automatic timing measurements (rise time, fall time, pulse width, PRI, PRF, duty cycle, and delay) and five automatic power measurement (peak power, average power, pulse top/base amplitude, and overshoot) with push-button ease. Front-panel operation is intuitive and straightforward. Data entries can be typed in or made with the front panel knob; automatic measurements are made with simple keystroke. The 8990A offers two sensor channels plus two external triggering/oscilloscope channels, allowing the simultaneous measurement of modulating signals and detector power envelopes.
* Amplitude and time markers for measuring power exactly where its needed
* Two oscilloscope channels for measuring time delay between video and microwave pulse
* Versatile triggering enables the capturing of exclusive glitches
* Waveform math functions for measuring scalar pulse parameters
* Dynamic Range: >45 dB
* Minimum Pulse Width: 20 ns
* Rise Time: <5 ns * Sensor and Video Inputs: 1 and 4; 2 and 3 -
Pulse Pattern Generator
TEKTRONIX PG 501
PULSE GENERATOR.
The PG501 provides simultaneous positive and negative 50 MHz output pulses with 5 ns rise and fall times and independently variable amplitudes from 0.5 V to 5 V into 50 Ω.
Front panel controls provide calibrated decade selection of pulse period from 20 ns to 20 ms, and duration from 10 ns to 10 ms. Uncalibrated pulse period from 20 ns to 0.2 s and duration from 10 ns to 0.1 s can be obtained with the variable control.
The PG501 has a gate input and a 10 ns pre-trigger output. -
RF Impedance/Material Analyzer
HP-Agilent/Keysight 4291B
Four component test fixtures (DUT size: 0.5 mm to 20 mm)
Independent parameter selection in 2 channels
Direct read-out permittivity, permeability (option)
Two material fixtures (operating temperature: -55deg C to + 200deg C)
Versatile analysis (temperature, cole-cole plot, relaxation time)
Sweep parameters (frequency, ac level, dc bias, temperature)The Keysight 4291B RF impedance / material analyzer provides a total solution for high-accuracy and easy measurement of surface-mount components and dielectric / magnetic materials. The Keysight 4291B uses a direct current-voltage measurement technique, opposing the reflection measurement technique, for more accurate impedance measurement over wide impedance range.
Basic impedance accuracy is +/- 0.8%. High Q accuracy enables low-loss component analysis. An internal synthesizer sweeps frequency from 1 MHz to 1.8 GHz with 1 mHz resolution. A 1.8-m error-less cable connects the analyzer to a test station so you can extend your test point away from the analyzer without losing accuracy. Advanced calibration and error compensation function eliminate measurement error factors in fixtures and assure high accuracy and repeatability at DUT / MUT.
The Hp 4291B also provides automatic level control and monitor of test signals by using IBASIC programming function; devices can be measured under a constant voltage or current. Measure bias dependent impedance characteristics with optional dc bias (up to 40 V and 100 mA). At the push of a button, the built-in Equivalent Circuit Analysis Function automatically calculates the circuit constant values of five circuit models.
The Hp 4291B has two measurement channels; each channel can be set to measure a single (e.g. Z) or dual (e.g. Z-theta) impedance parameter. The color TFT with split-display can show both active traces and memory traces (stored in RAM). A built-in floppy disk drive stores programs and test data in either LIF or MS-DOS format. With built-in IBASIC, you can control external test equipment such as a temperature chamber or wafer prober directly from the Keysight 4291B. You do not need a separate instrument controller.
Material Evaluation
The Hp 4291B enables easy and sophisticated material evaluation and improves material evaluation quality and efficiency. The Hp 4291B provides the total dielectric / magnetic material measurement solutions in wide frequency range (1 MHz to 1 GHz).
Datasheet -
Power Meter
ROHDE & SCHWARZ NRVS
Uncompromizing technology and
ease of operation make the NRVS an
ideal instrument for any kind of power
measurement in manifold laboratory
and system applications. Thanks to its
unique measuring heads with calibra-
tion data memory and temperature
sensor, which make adjustments by
the user superfluous, the NRVS meas-
ures at all times with high accuracy
and free of operator’s errors.
The range of measuring heads includes thermal power sensors as well as highly sensitive diode power sensors, peak power
sensors, probes and insertion units for voltage measurements. The NRVS covers a power span from 100 pW up to the
kW range. In addition to the power sensors, all voltage probes of the URV5-Z series can be used.
Datasheet -
Cable
HP-Agilent/Keysight 11730A Sensore di potenza / Cavo sorgente rumore SNS (1,5 m / 5 piedi)
The Keysight 11730A/B/C/D/E cables are used with the N8480/8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements. The Keysight 11730A/B/C can also be used in conjunction with the SNS series noise sources which are designed to operate with the NFA Series Noise Figure Analyzers
-
Oscilloscope 2 channels
Rigol MSO4012
100MHz, 2 channel, 4GS/s
MSO4000 Series is the new mainstream digital scope to meet the customer’s applications with its innovative technology, industry leading specifications, powerful trigger functions and broad analysis capabilities. – Bandwidth 100MHz – Sample Rate Analog channel up to 4 GSa/s, Digital Channel up to 1 GSa/s(MSO) – Standard Memory depth: Analog channel up to 140 Mpts, Digital Channel up to 28 Mpts(MSO) – 2 Analog Channels, 16 Digital channels(MSO) – Waveform capture rate Up to 110,000 waveforms per second, – Real Time Waveform Record, Replay & Analysis(Std. up to 200,000 frames) – Lower noise floor, the Min. vertical sensitivity is 1mV/div – Innovative “UltraVision” technology – A variety of Trigger functions – Support serial bus trigger(Std.) and decoding(Opt.) for both analog and digital channels – Complete Connectivity: USB Host& Device, LAN(LXI-C), VGA, AUX,USB-GPIB(Opt.) – 9 inch WVGA(800X480), 256 level intensity grading display
-
Power Supply
HP E3616A 60W Power Supply, 35V, 1.7A
Keysight basic DC power supplies offer essential features for a tight budget.
The single output, 30-60 W, E3610A-E3617A provide small, compact size for bench use; low-noise and excellent regulation; and dual-range outputs (E3610A/11A/12A).
The Keysight 60W, single output E3616A is a reliable and convenient power for benchtop use, and offers solid performance and a variety of basic and enhanced capabilities.Output Ratings (Maximum current is derated 1% per °C between 40° to 55°C)
> Range 1: 0 to 35 V, 0 to 1.7 A
> Range 2: NA
> Power (max): 60 WRipple & Noise from 20 Hz to 20 MHz
> Voltage rms: 200 µV
> Peak-to-Peak: 1 mVLoad & Line Regulation
> 0.01% + 2 mVMeter Resolution
> Voltage: 10 mV (0-20 V), 100 mV (>20 V)
> Current: 1 mA -
PEAK POWER SENSOR
HP 8991A Peak Power Meter
The HP 8991A peak power analyzer provides complete and accurate characterization of today's complex pulsed signals. It is capable of performing seven automatic timing measurements (rise time, fall time, pulse width, PRI, PRF, duty cycle, and delay) and five automatic power measurement (peak power, average power, pulse top/base amplitude, and overshoot) with push-button ease. Front-panel operation is intuitive and straightforward. Data entries can be typed in or made with the front panel knob; automatic measurements are made with simple keystroke. The 8990A offers two sensor channels plus two external triggering/oscilloscope channels, allowing the simultaneous measurement of modulating signals and detector power envelopes.
* Amplitude and time markers for measuring power exactly where its needed
* Two oscilloscope channels for measuring time delay between video and microwave pulse
* Versatile triggering enables the capturing of exclusive glitches
* Waveform math functions for measuring scalar pulse parameters
* Dynamic Range: >45 dB
* Minimum Pulse Width: 20 ns
* Rise Time: <5 ns * Sensor and Video Inputs: 1 and 4; 2 and 3 -
Pulse Pattern Generator
TEKTRONIX PG 501
PULSE GENERATOR.
The PG501 provides simultaneous positive and negative 50 MHz output pulses with 5 ns rise and fall times and independently variable amplitudes from 0.5 V to 5 V into 50 Ω.
Front panel controls provide calibrated decade selection of pulse period from 20 ns to 20 ms, and duration from 10 ns to 10 ms. Uncalibrated pulse period from 20 ns to 0.2 s and duration from 10 ns to 0.1 s can be obtained with the variable control.
The PG501 has a gate input and a 10 ns pre-trigger output. -
RF Impedance/Material Analyzer
HP-Agilent/Keysight 4291B
Four component test fixtures (DUT size: 0.5 mm to 20 mm)
Independent parameter selection in 2 channels
Direct read-out permittivity, permeability (option)
Two material fixtures (operating temperature: -55deg C to + 200deg C)
Versatile analysis (temperature, cole-cole plot, relaxation time)
Sweep parameters (frequency, ac level, dc bias, temperature)The Keysight 4291B RF impedance / material analyzer provides a total solution for high-accuracy and easy measurement of surface-mount components and dielectric / magnetic materials. The Keysight 4291B uses a direct current-voltage measurement technique, opposing the reflection measurement technique, for more accurate impedance measurement over wide impedance range.
Basic impedance accuracy is +/- 0.8%. High Q accuracy enables low-loss component analysis. An internal synthesizer sweeps frequency from 1 MHz to 1.8 GHz with 1 mHz resolution. A 1.8-m error-less cable connects the analyzer to a test station so you can extend your test point away from the analyzer without losing accuracy. Advanced calibration and error compensation function eliminate measurement error factors in fixtures and assure high accuracy and repeatability at DUT / MUT.
The Hp 4291B also provides automatic level control and monitor of test signals by using IBASIC programming function; devices can be measured under a constant voltage or current. Measure bias dependent impedance characteristics with optional dc bias (up to 40 V and 100 mA). At the push of a button, the built-in Equivalent Circuit Analysis Function automatically calculates the circuit constant values of five circuit models.
The Hp 4291B has two measurement channels; each channel can be set to measure a single (e.g. Z) or dual (e.g. Z-theta) impedance parameter. The color TFT with split-display can show both active traces and memory traces (stored in RAM). A built-in floppy disk drive stores programs and test data in either LIF or MS-DOS format. With built-in IBASIC, you can control external test equipment such as a temperature chamber or wafer prober directly from the Keysight 4291B. You do not need a separate instrument controller.
Material Evaluation
The Hp 4291B enables easy and sophisticated material evaluation and improves material evaluation quality and efficiency. The Hp 4291B provides the total dielectric / magnetic material measurement solutions in wide frequency range (1 MHz to 1 GHz).
Datasheet -
Power Meter
ROHDE & SCHWARZ NRVS
Uncompromizing technology and
ease of operation make the NRVS an
ideal instrument for any kind of power
measurement in manifold laboratory
and system applications. Thanks to its
unique measuring heads with calibra-
tion data memory and temperature
sensor, which make adjustments by
the user superfluous, the NRVS meas-
ures at all times with high accuracy
and free of operator’s errors.
The range of measuring heads includes thermal power sensors as well as highly sensitive diode power sensors, peak power
sensors, probes and insertion units for voltage measurements. The NRVS covers a power span from 100 pW up to the
kW range. In addition to the power sensors, all voltage probes of the URV5-Z series can be used.
Datasheet -
Cable
HP-Agilent/Keysight 11730A Sensore di potenza / Cavo sorgente rumore SNS (1,5 m / 5 piedi)
The Keysight 11730A/B/C/D/E cables are used with the N8480/8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements. The Keysight 11730A/B/C can also be used in conjunction with the SNS series noise sources which are designed to operate with the NFA Series Noise Figure Analyzers
€0.00 View Product -
Oscilloscope 2 channels
Rigol MSO4012
100MHz, 2 channel, 4GS/s
MSO4000 Series is the new mainstream digital scope to meet the customer’s applications with its innovative technology, industry leading specifications, powerful trigger functions and broad analysis capabilities. – Bandwidth 100MHz – Sample Rate Analog channel up to 4 GSa/s, Digital Channel up to 1 GSa/s(MSO) – Standard Memory depth: Analog channel up to 140 Mpts, Digital Channel up to 28 Mpts(MSO) – 2 Analog Channels, 16 Digital channels(MSO) – Waveform capture rate Up to 110,000 waveforms per second, – Real Time Waveform Record, Replay & Analysis(Std. up to 200,000 frames) – Lower noise floor, the Min. vertical sensitivity is 1mV/div – Innovative “UltraVision” technology – A variety of Trigger functions – Support serial bus trigger(Std.) and decoding(Opt.) for both analog and digital channels – Complete Connectivity: USB Host& Device, LAN(LXI-C), VGA, AUX,USB-GPIB(Opt.) – 9 inch WVGA(800X480), 256 level intensity grading display