ItalianoShop
Showing 1321–1350 of 1386 results
-
Digital Multimeter
Flir T910973
– Quickly indicates the moisture content of materials with Pinless technology without damaging the surface
– Remote Pin-type probe (MO290-P included) allows for contact moisture readings (3ft/0.9m cable length) – Manually store/recall up to 20 labeled readings
– Works on multiple wood types and other building materials
– Easy to read, large dual display with automatic backlight feature
– Simultaneously displays moisture value of wood or material being tested, Air Temperature, IR Temperature, or Humidity
– Pinless measurement depth to 0.75″ (19mm) below the surface
– Programmable high/low Moisture and Humidity alarms – Designed with a patented IR circuit to measure non-contact surface temperature
– 8:1 distance to spot ratio with 0.95 fixed emissivity
– Built-in Humidity/Temperature probe measures Relative Humidity, Air
– Temperature plus Grains Per Pound (GPP)/(g/kg), Dew Point (DP),
– Vapor Pressure, and condensation point
– Fast Analog Bargraph, Min/Max and Data Hold, Auto power off and low battery indication
– MeterLink Bluetooth transmitter wirelessly transmits moisture and humidity data to selected FLIR thermal imaging IR cameras to incorporate meter readings with thermal images
– Complete with pin moisture probe with cable, 9V battery and caseSKU: 279 -
System DC Elettronic Load
HP-Agilent/Keysight 6050A
The Agilent 6050A electronic load mainframe accepts user-installable Agilent load modules for easy system configuration and future reconfiguration. The 6050A holds up to six 60501B, 60502B, and 60503B load modules, or three 60504B and 60507B load modules, allowing up to 1,800 watts of total maximum power. One GPIB address is all you need for complete control and readback of all load modules within a single mainframe. – GPIB control of current, voltage and resistance – GPIB readback of current, voltage, and power – Built-in pulse waveform generation with programmable amplitude, frequency, duty cycle and slew rate – Full protection from over-current, over-voltage, overpower, over-temperature, and reverse polarity – Electronic calibration – Trigger for external synchronization – Parallel units in constant current mode for higher power – VXI plug & play drivers
SKU: 388 -
EPM Series Single-Channel Power Meter
HP-Agilent/Keysight E4418B
The E4418B is a power meter is designed for bench and automatic test equipment (ATE) use.
> Fast measurement speed (up to 200 readings per second, over the GPIB, with E-series sensors)
> Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
> No range-switching delays with 8480 series sensors, and only one fast-range switch point with E-series sensors
> Code compatibility with 437B and 436A power meters
> GPIB and RS232 connector for remote control of all functions
> Option 002 Rear Panel Power Sensor Connection OptionSKU: 1263 -
Transmission Analyzers
HP 37721A Digital Transmission Analyzer opt. 001-003
The 37718A communications performance analyzer is a single-box portable multi-rate BER and jitter tester up to 2.5 Gb/s (OC-48/STM-16) for development, qualification and manufacture of SONET, SDH, ATM and POS network equipment, sub-assemblies, line cards and devices.
* ATM and POS test capability to 2.5 Gb/s
* Concatenated payloads at all synchronous rates up to 2.5 Gb/s
* SmartTest facility for fast test setup
* Automatic detection of mixed payload signal structures
* Accurate measurement of protection switching times (ring and linear networks)
* Jitter generation and measurement at all rates (1.5, 2, 8, 34, 45, 140, 52, 155, 622 and 2,488 Mb/s)
* Jitter testing to ITU-T and Telcordia recommendationsSKU: n/a -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
DatasheetSKU: n/a -
Power Sensor
HP-Agilent/Keysight 8481A
HP AGILENT KEYSIGHT 8481A POWER SENSOR 10 MHz to 18 GHz
The 8481A power sensor is designed for use with the 435A/B, 436A, 437A, 438A, 70100A, EPM series, EPM-P series, E1416A, N1911A, N1912A, N1913A, and N1914A power meters.
The 8481A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 10 MHz to 18 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -30 dBm to +20 dBm)
• 50 ohm impedance
• N (m) connectorSKU: n/a -
Noise Figure Meter
HP-Agilent/Keysight 8970A
Agilent HP 8970A Noise Figure Meter. Features and specifications of the HP 8970A include:
– Frequency Range: 10 MHz to 1600 MHz
– Noise Figure Measurement Range: 0 to 30 dB
– NF Instrumentation Uncertainty: +0.1 dB
– Gain Measurement Range: -20 to+40 dB
– Gain Instrumentation Uncertainty: +0.15 dB
– Input SWR reference impedence: <1.7 10 MHz to 1600 MHz
– Requires 346A/B/C noise source .
DatasheetSKU: n/a
-
Digital Multimeter
Flir T910973
– Quickly indicates the moisture content of materials with Pinless technology without damaging the surface
– Remote Pin-type probe (MO290-P included) allows for contact moisture readings (3ft/0.9m cable length) – Manually store/recall up to 20 labeled readings
– Works on multiple wood types and other building materials
– Easy to read, large dual display with automatic backlight feature
– Simultaneously displays moisture value of wood or material being tested, Air Temperature, IR Temperature, or Humidity
– Pinless measurement depth to 0.75″ (19mm) below the surface
– Programmable high/low Moisture and Humidity alarms – Designed with a patented IR circuit to measure non-contact surface temperature
– 8:1 distance to spot ratio with 0.95 fixed emissivity
– Built-in Humidity/Temperature probe measures Relative Humidity, Air
– Temperature plus Grains Per Pound (GPP)/(g/kg), Dew Point (DP),
– Vapor Pressure, and condensation point
– Fast Analog Bargraph, Min/Max and Data Hold, Auto power off and low battery indication
– MeterLink Bluetooth transmitter wirelessly transmits moisture and humidity data to selected FLIR thermal imaging IR cameras to incorporate meter readings with thermal images
– Complete with pin moisture probe with cable, 9V battery and case -
System DC Elettronic Load
HP-Agilent/Keysight 6050A
The Agilent 6050A electronic load mainframe accepts user-installable Agilent load modules for easy system configuration and future reconfiguration. The 6050A holds up to six 60501B, 60502B, and 60503B load modules, or three 60504B and 60507B load modules, allowing up to 1,800 watts of total maximum power. One GPIB address is all you need for complete control and readback of all load modules within a single mainframe. – GPIB control of current, voltage and resistance – GPIB readback of current, voltage, and power – Built-in pulse waveform generation with programmable amplitude, frequency, duty cycle and slew rate – Full protection from over-current, over-voltage, overpower, over-temperature, and reverse polarity – Electronic calibration – Trigger for external synchronization – Parallel units in constant current mode for higher power – VXI plug & play drivers
-
EPM Series Single-Channel Power Meter
HP-Agilent/Keysight E4418B
The E4418B is a power meter is designed for bench and automatic test equipment (ATE) use.
> Fast measurement speed (up to 200 readings per second, over the GPIB, with E-series sensors)
> Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
> No range-switching delays with 8480 series sensors, and only one fast-range switch point with E-series sensors
> Code compatibility with 437B and 436A power meters
> GPIB and RS232 connector for remote control of all functions
> Option 002 Rear Panel Power Sensor Connection Option -
Transmission Analyzers
HP 37721A Digital Transmission Analyzer opt. 001-003
The 37718A communications performance analyzer is a single-box portable multi-rate BER and jitter tester up to 2.5 Gb/s (OC-48/STM-16) for development, qualification and manufacture of SONET, SDH, ATM and POS network equipment, sub-assemblies, line cards and devices.
* ATM and POS test capability to 2.5 Gb/s
* Concatenated payloads at all synchronous rates up to 2.5 Gb/s
* SmartTest facility for fast test setup
* Automatic detection of mixed payload signal structures
* Accurate measurement of protection switching times (ring and linear networks)
* Jitter generation and measurement at all rates (1.5, 2, 8, 34, 45, 140, 52, 155, 622 and 2,488 Mb/s)
* Jitter testing to ITU-T and Telcordia recommendations -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Sensor
HP-Agilent/Keysight 8481A
HP AGILENT KEYSIGHT 8481A POWER SENSOR 10 MHz to 18 GHz
The 8481A power sensor is designed for use with the 435A/B, 436A, 437A, 438A, 70100A, EPM series, EPM-P series, E1416A, N1911A, N1912A, N1913A, and N1914A power meters.
The 8481A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 10 MHz to 18 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -30 dBm to +20 dBm)
• 50 ohm impedance
• N (m) connector -
Noise Figure Meter
HP-Agilent/Keysight 8970A
Agilent HP 8970A Noise Figure Meter. Features and specifications of the HP 8970A include:
– Frequency Range: 10 MHz to 1600 MHz
– Noise Figure Measurement Range: 0 to 30 dB
– NF Instrumentation Uncertainty: +0.1 dB
– Gain Measurement Range: -20 to+40 dB
– Gain Instrumentation Uncertainty: +0.15 dB
– Input SWR reference impedence: <1.7 10 MHz to 1600 MHz
– Requires 346A/B/C noise source .
Datasheet
-
Digital Multimeter
Flir T910973
– Quickly indicates the moisture content of materials with Pinless technology without damaging the surface
– Remote Pin-type probe (MO290-P included) allows for contact moisture readings (3ft/0.9m cable length) – Manually store/recall up to 20 labeled readings
– Works on multiple wood types and other building materials
– Easy to read, large dual display with automatic backlight feature
– Simultaneously displays moisture value of wood or material being tested, Air Temperature, IR Temperature, or Humidity
– Pinless measurement depth to 0.75″ (19mm) below the surface
– Programmable high/low Moisture and Humidity alarms – Designed with a patented IR circuit to measure non-contact surface temperature
– 8:1 distance to spot ratio with 0.95 fixed emissivity
– Built-in Humidity/Temperature probe measures Relative Humidity, Air
– Temperature plus Grains Per Pound (GPP)/(g/kg), Dew Point (DP),
– Vapor Pressure, and condensation point
– Fast Analog Bargraph, Min/Max and Data Hold, Auto power off and low battery indication
– MeterLink Bluetooth transmitter wirelessly transmits moisture and humidity data to selected FLIR thermal imaging IR cameras to incorporate meter readings with thermal images
– Complete with pin moisture probe with cable, 9V battery and case -
System DC Elettronic Load
HP-Agilent/Keysight 6050A
The Agilent 6050A electronic load mainframe accepts user-installable Agilent load modules for easy system configuration and future reconfiguration. The 6050A holds up to six 60501B, 60502B, and 60503B load modules, or three 60504B and 60507B load modules, allowing up to 1,800 watts of total maximum power. One GPIB address is all you need for complete control and readback of all load modules within a single mainframe. – GPIB control of current, voltage and resistance – GPIB readback of current, voltage, and power – Built-in pulse waveform generation with programmable amplitude, frequency, duty cycle and slew rate – Full protection from over-current, over-voltage, overpower, over-temperature, and reverse polarity – Electronic calibration – Trigger for external synchronization – Parallel units in constant current mode for higher power – VXI plug & play drivers
-
EPM Series Single-Channel Power Meter
HP-Agilent/Keysight E4418B
The E4418B is a power meter is designed for bench and automatic test equipment (ATE) use.
> Fast measurement speed (up to 200 readings per second, over the GPIB, with E-series sensors)
> Speed improvement of x2 using the 8480 series power sensor (compared to the 437B)
> No range-switching delays with 8480 series sensors, and only one fast-range switch point with E-series sensors
> Code compatibility with 437B and 436A power meters
> GPIB and RS232 connector for remote control of all functions
> Option 002 Rear Panel Power Sensor Connection Option -
Transmission Analyzers
HP 37721A Digital Transmission Analyzer opt. 001-003
The 37718A communications performance analyzer is a single-box portable multi-rate BER and jitter tester up to 2.5 Gb/s (OC-48/STM-16) for development, qualification and manufacture of SONET, SDH, ATM and POS network equipment, sub-assemblies, line cards and devices.
* ATM and POS test capability to 2.5 Gb/s
* Concatenated payloads at all synchronous rates up to 2.5 Gb/s
* SmartTest facility for fast test setup
* Automatic detection of mixed payload signal structures
* Accurate measurement of protection switching times (ring and linear networks)
* Jitter generation and measurement at all rates (1.5, 2, 8, 34, 45, 140, 52, 155, 622 and 2,488 Mb/s)
* Jitter testing to ITU-T and Telcordia recommendations -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Sensor
HP-Agilent/Keysight 8481A
HP AGILENT KEYSIGHT 8481A POWER SENSOR 10 MHz to 18 GHz
The 8481A power sensor is designed for use with the 435A/B, 436A, 437A, 438A, 70100A, EPM series, EPM-P series, E1416A, N1911A, N1912A, N1913A, and N1914A power meters.
The 8481A provides extraordinary accuracy, stability, and lower SWR.
• Excellent SWR for reducing mismatch uncertainty
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)
• Compatible with EPM, EPM-P and P-series power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -30 to +20 dBm
• Frequency range 10 MHz to 18 GHz
• Thermocouple power sensing element
• Measurement range: 1 µW to 100 mW ( -30 dBm to +20 dBm)
• 50 ohm impedance
• N (m) connector -
Noise Figure Meter
HP-Agilent/Keysight 8970A
Agilent HP 8970A Noise Figure Meter. Features and specifications of the HP 8970A include:
– Frequency Range: 10 MHz to 1600 MHz
– Noise Figure Measurement Range: 0 to 30 dB
– NF Instrumentation Uncertainty: +0.1 dB
– Gain Measurement Range: -20 to+40 dB
– Gain Instrumentation Uncertainty: +0.15 dB
– Input SWR reference impedence: <1.7 10 MHz to 1600 MHz
– Requires 346A/B/C noise source .
Datasheet