ItalianoPower Supply
Showing 1–30 of 93 results
-
Power Supply
RIGOL DP932A
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/OSKU: n/a€690.00 View Product -
Power Supply
RIGOL DP2031
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 5 A, DC, max 222 W). 4.3-inch LCD color touch screen. High resolution for measurement of 1 μA low range current. Low output ripple and noise <350 μVrms/2 mVpp. USB HOST, LAN, Digital I/O, and RS232 (standard)
3 electrically isolated independent channels with a maximum total power of up to 222 W
32 V/3 A || 32 V/3 A || 6 V/5 A (standard)
32 V/2 A || 32 V/2 A || 6 V/10 A (optional)
4.3-inch LCD color touch screen
Internal series/parallel connections for CH1 and CH2
High resolution for measurement of 1 μA low range current
Capability to measure and display wide dynamic ranges of current
Excellent programming/readback accuracy
Transient response time <50 μs
Front and rear output terminals
2-wire or 4-wire remote sense
A maximum of 512 arbitrary points with dwell time down to 1 ms; various built-in basic waveforms
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Automatic switchover between low and high range measurement
Timing output, energy consumption analysis (IoT), data logging and analysis
Capability to measure the minimum of 1 ms pulse current
Three rack-units (3U), 1/2-rack form factor
Software control
Over voltage, over current, and over temperature protection
Various interfaces available: USB HOST, LAN, Digital I/O, and RS232 (standard)SKU: n/a€1,099.00 View Product -
Power Supply
RIGOL DP932U
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/OSKU: n/a€529.00 View Product -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions.SKU: n/a€599.00 View Product -
Power Supply
RIGOL DP932E
The DP900 Series Power Supplies combine our new touch screen interface with new flexibility and higher speed functions designed for benchtop DC power analysis. The DP932A and DP932U are 3 channel completely isolated benchtop power supplies. Activate the high-speed arb function that allows you to update the power supply output at up to 10 times per second while quickly creating a repeating shape or pattern from the front panel. You can also combine channels 1 and 2 internally either in parallel or in series to expand the power envelope for your testing. No more cabling challenges since you can now get the current or voltage for both channels with one cable connection. The DP932A comes with all the capabilities enabled. The DP932U has optional resolution, digital IO, and arbitrary speed upgrades. The DP932U also comes with safety banana plugs in place of the binding posts on the DP932A. This combination of flexibility and capability makes the DP900 an important addition to any engineer’s bench.
SKU: n/a€425.00 View Product -
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
SKU: n/a€589.00 View Product -
Power Supply
AGILENT-Hp/Keysight E3631A
The triple output, 80 W, GPIB, E3631A provides small, compact size for bench use; low output ripple and noise; built-in measurements and basic programmable features with GPIB and RS232 interface. This clean and reliable supply is designed for general purpose applications; and combines convenient benchtop capabilities with flexible system features in a compact, multi-output package.
Output 1: 0 to 6 V, 0 to 5 A
Output 2: 0 to +25 V, 0 to 1 A
Output 3: 0 to -25 V, 0 to 1 A
Programming Accuracy at 25°C ±5°C
Voltage: 0.05% + 20 mV, 0.05% + 20 mV, 0.1% + 5 mV
+ Current: 0.15% + 4 mA, 0.15% + 4 mA, 0.2% + 10 mA
Normal Mode Voltage: <350 µVrms/ 2 mV p-p, <350 µV rms/2 mV p-p, <350 µV rms/2 mV p-p Normal-mode current: <500 µA rms, <500 µA rms, <2 mA rms Common-mode current: <1.5 µA rms, <1.5 µA rms, <1.5 µA rms Readback Accuracy at 25°C ±5° 1200W, DC System Power Supplies,60V - 50A. DatasheetSKU: n/a -
Power Supply
HP-Agilent/Keysight 6012B
These single-output supplies can replace multiple units, saving rack space and reducing system cost and complexity.
Autoranging outputs provide maximum power at a variety of operating points
Overvoltage features protect DUTs quickly and automatically
Auto-parallel or auto-series connections enable greater output flexibility
Ten-turn pots for precise local control1200W, DC System Power Supplies,60V – 50A.
DatasheetSKU: n/a -
Power Supply
AGILENT-Hp/Keysight N5748A
Output Ratings
Voltage: 80 V
Current: 9.5 A
Power: 760 WThe single output, 760W N5748A, provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers reliable performance and enhanced capabilities in a compact 1U package.
SKU: n/a -
Power Supply
KEYSIGHT – Agilent/Hp N8740A
Keysight's basic DC power supplies offer essential features for a tight budget. The Keysight N8740A is a 150 V, 22 A, 3300 W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
Please select the AC input voltage option carefully. The AC input voltage hardware is permanently installed at the factory and cannot be changed under any circumstances after delivery. If the wrong AC input voltage option is purchased and delivered, the unit would need to be returned. Product returns are subject to Keysight approval and applicable charges. A new order would then have to be placed.
DC output ratingsVoltage: 150 V
Current: 22 A
Power: 3300 WProgramming accuracy
Voltage: 0.05% + 75 mV
Current: 0.1% + 44 mAOutput ripple and noise
CV p-p: 100 mV
CV rms: 25 mV
DatasheetSKU: n/a -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
DatasheetSKU: n/a€729.00 View Product -
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
DatasheetSKU: n/a€710.00 View Product -
Power Supply
AGILENT-Hp/Keysight 6675A
Output Ratings
Output voltage: 0 to 120 V
Output current (40°C): 0 to 18 AProgramming Accuracy at 25°C ±5°C
Voltage 0.04% + 120 mV
Current 0.1% + 12 mARipple & Noise from 20 Hz to 20 MHz
Voltage rms: 1.9 mV
Peak-to-Peak: 16 mV
Current rms: 12 mAHp high performance DC power supplies offer speed and accuracy for test optimization. The single output, 2000 W GPIB 6671A-6675A provide fast, low-noise outputs; analog control of output voltage and current; and fan-speed control to minimize acoustic noise.
The Hp 2160W, GPIB, single output 6675A is a highly efficient low-noise supply that maximize test throughput and is designed to offer excellent reliability, low ripple and noise, and extremely accurate built-in measurements of voltage and current.
DatasheetSKU: n/a -
Power Supply
ELIND 3232
Electronic linear laboratory bench power supply model ELIND 328. Suitable for professional use. Adjustable in voltage and current: 0-32V and 0-3.2A continuous (DC). Outputs isolated from the ground (can therefore also be used with the positive to ground). Multiturn knob for fine tension adjustment. Tool to monitor voltage or current. Excellent condition. Used very little. Dimensions: 14.5×9.5x25cm. Weight 2Kg. 220V AC cable power supply
SKU: n/a -
Power Supply
AGILENT-Hp/Keysight 6645A
Questa serie di alimentatori CC regolati lineari da 200 W è progettata per massimizzare la produttività dei DUT attraverso il processo di test di produzione con tempi di programmazione rapidi su e giù.
I preziosi insiemi possono essere distrutti da un guasto minore di un componente che può consentire un flusso di tensione o corrente che fluisce verso il DUT. Le funzioni di protezione rapida, tra cui il piede di porco rapido, la protezione crossover in modalità e la possibilità di collegare i circuiti di protezione di più alimentatori possono aumentare il rendimento di produzione.
La programmazione dell'uscita CC e delle funzioni di protezione può essere effettuata dal pannello frontale o utilizzando i comandi SCPI standard del settore, tramite GPIB. Utilizzando il collegamento seriale, è possibile collegare fino a 16 alimentatori tramite un indirizzo GPIB. L'integrazione del sistema di test può essere ulteriormente semplificata utilizzando i driver VXIplug & play. La tensione e la corrente di uscita possono anche essere controllate con segnali analogici. Ciò è utile per alcuni tipi di ambienti rumorosi e anche per reazioni immediate ai cambiamenti di processo.Tensione flottante CC: i terminali di uscita possono essere fatti galleggiare fino a ± 240 V CC dalla terra del telaio.
Telerilevamento: è possibile far cadere fino a metà della tensione di uscita nominale in ciascun cavo di carico. La caduta del carico comporta la sottrazione della tensione disponibile per il carico.
Tempo di elaborazione del comando: il tempo medio necessario affinché la tensione di uscita inizi a cambiare in seguito alla ricezione di dati digitali è di 20 ms per gli alimentatori collegati direttamente al GPIB.
Tempo di risposta della programmazione dell'uscita: il tempo di salita e discesa (10/90% e 90/10%) della tensione di uscita è inferiore a 15 ms. La variazione della tensione di uscita si assesta entro 1 LSB (0,025% x tensione nominale) del valore finale in meno di 60 ms.
Programmazione verso il basso: un programmatore attivo verso il basso affonda circa il 20% della corrente di uscita nominale.Valori nominali di uscita
Tensione di uscita: da 0 a 120 V.
Corrente di uscita (40 ° C): da 0 a 1,5 A
Corrente massima (50 ° C / 55 ° C): 1,4 A / 1,3 APrecisione di programmazione a 25 ° C ± 5 ° C
Tensione 0,06% + 51 mV
Corrente 0,15% + 1,7 mARipple & Noise (20 Hz – 20 MHz)
Voltaggio rms: 700 µV
Tensione picco-picco: 7 mV
Corrente efficace: 1 mA
Scheda TecnicaSKU: n/a -
Power Supply
HP-Agilent/Keysight 6645A
HP high performance DC power supplies offer speed and accuracy for test optimization. The single output, 200 W, GPIB 6641A-6645A provide fast, low-noise outputs; analog control of output voltage and current; fan-speed control to minimize acoustic noise; as well as parallel and series connections of multiple units.
The HP 180W, GPIB, single output 6645A is a versatile programmable supply designed to maximize test throughput during design verification or on the production line, and is fully programmable to help reduce test time through a variety of automated capabilities.
Output Ratings
Output voltage: 0 to 120 V
Output current (40° C): 0 to 1.5 A
Maximum current (50° C/55° C): 1.4 A/1.3 AProgramming Accuracy at 25°C ±5°C
Voltage 0.06% + 51 mV
Current 0.15% + 1.7 mARipple & Noise (20 Hz – 20 MHz)
Voltage rms: 700 µV
Voltage peak-to-peak: 7 mV
Current rms: 1 mA
DatasheetSKU: n/a -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
DatasheetSKU: n/a -
Power Supply
KEYSIGHT N8940A
KEYSIGHT N8940A Alimentatore CC con autoranging, 80 V, 170 A, 5000 W, 400 V CA.
La serie Keysight N8900 offre alimentazione CC programmabile a uscita singola programmabile da 5 kW, 10 kW e 15 kW per applicazioni ATE che richiedono la giusta quantità di prestazioni al giusto prezzo. La caratteristica di uscita a regolazione automatica degli alimentatori serie N8900 consente una flessibilità senza precedenti offrendo una vasta gamma di combinazioni di tensione e corrente a piena potenza. Gli alimentatori con caratteristiche di uscita “rettangolari” o tradizionali forniscono piena potenza con una sola combinazione di tensione e corrente. Solo un N8900 fa il lavoro di più alimentatori. È come avere molti alimentatori in uno!
La serie N8900 offre potenza di uscita stabile, misurazioni di tensione e corrente incorporate e tensione e corrente di uscita con autorangolazione da 80 V a 1500 V e da 10 A a 510 A. Questi alimentatori offrono molte funzionalità pronte per il sistema come interfacce I / O standard multiple per semplificare e accelerare lo sviluppo del sistema di test e il design compatto 3U per risparmiare spazio nel rack. Se è necessaria più potenza, è possibile mettere in parallelo più unità N8900 per creare un “unico” alimentatore con> 100 kW di potenza totale in uscita. Il controllo master / slave incorporato consente la programmazione come se fosse solo un grande alimentatore; non è necessario programmare ciascuna fornitura singolarmente.Uscita autoranging – fa il lavoro di più alimentatori!
Potenza di uscita massima di 5 kW, 10 kW e 15 kW
Fino a 1500 V e fino a 510 A
14 diverse combinazioni di tensione, corrente e potenza disponibili in 208 V CA o 400 V CA (28 modelli in totale)
La giusta quantità di prestazioni al giusto prezzo
Unità facilmente parallele per creare un “unico” alimentatore con> 100 kW di potenza
Misura di tensione e corrente incorporata
Alta densità di potenza, 15 kW in soli 3U (5,25 “/ 13,34 cm)
Protezione da sovratensione, sovracorrente e sovratemperatura
Interfacce LAN (LXI Core), USB, GPIB e analogiche tutte standardValori nominali DC
Voltaggio: da 0 a 80 V.
Corrente: da 0 a 170 A
Potenza: 5000 W.Ingresso AC
Intervallo di tensione: 360-440 V CA.
Accuratezza della programmazione
Tensione: 0,1% del fondo scala
Corrente: 0,2% del fondo scala
Scheda TecnicaSKU: n/a -
Power Supply
H10S CLT-100
Exclusive power supply is required for DC screwdrivers.
● Exclusive power supply converts the electric current from AC outlet (on the primary side) to low-voltage output (HI: DC30V) or (LOW: about DC20V) to supply it to the screwdriver.
● Safe and quiet rotation.
● Please always use HIOS screwdriver in combination with HIOS power supply for safe screw tightening.
● Stable power supply with multiple inputs (AC100V to 240V).
(Not applicable to CLT-100 and MC-70L)SKU: n/a€120.00 View Product -
Power Supply
HP/AGILENT/KEYSIGHT E3615A
HP basic DC power supplies offer essential features for a tight budget. The single output, 30-60 W, E3610A-E3617A provide small, compact size for bench use; low-noise and excellent regulation; and dual-range outputs (E3610A/11A/12A). The HP 60W, single output E3615A is a reliable and convenient power for benchtop use, and offers solid performance and a variety of basic and enhanced capabilities.
The E3600 Series of low-cost benchtop power supplies give you the performance of system power supplies at a decent price. All E3600 family members provide clean power with excellent regulation and a fast transient response. The E3600 Series single-output non-programmable models are described on this page. Refer to page 3 for information on dual-output and triple-output non- programmable models.
All E3600 Series single-output non-programmable power supplies feature separate digital-panel meters for monitoring voltage and current simultaneously, giving you precise reading and control capability. All models also feature 10-turn potentiometers for accurate adjustment of voltage and current output settings.
With 0.01 percent load and line regulation, these instruments keep the output steady when power line and load changes occur.
The low normal mode noise specification of less than 200 μVrms ensures clean power for precision circuitry.In all single-output models, either the positive or negative terminal can be connected to ground, providing a positive or negative voltage output. Outputs can also be floated up to 240 V from ground.
These instruments also feature adjustable current limits, letting you set the safest current limit without having to short the output.
These popular 30-watt bench supplies are designed for general laboratory use. The constant-voltage, constant-current output allows operation as either a voltage or current source. The changeover occurs automatically, based on the load. Each of these models has two ranges, allowing more current at a lower voltage. For higher output voltages, supplies can be connected in series. These models also feature overload protection. A continuously acting constant current curcuit protects the power supply against all overloads including a direct short placed across the terminals in a constant voltage operation.
These fexible 60-watt, single-range power supplies can be used as either voltage or current sources. When the output terminal voltage increases to a preset shut-down level, an overvoltage protection circuit disables the output to protect the device under test (DUT) for damage. The overvoltage protection feature can be easily monitored and adjusted from the front panel.
Using the remote sensing capability, these instruments automatically compensate for voltage drop in the load leads, so you obtain an accurate voltage at the DUT.
Using the remote analog voltage programming capability, these instruments can remotely vary the voltage, so you are able to control the regulation output voltage or current.
Output Ratings (Maximum current is derated 1% per °C between 40° to 55°C)
- Range 1: 0 to 20 V, 0 to 3 A
- Range 2: NA
- Power (max): 60 W
Ripple & Noise from 20 Hz to 20 MHz
- Voltage rms: 200 µV
- Peak-to-Peak: 1 mV
Load & Line Regulation
- 0.01% + 2 mV
Meter Resolution
- Voltage: 10 mV (0-20 V), 100 mV (>20 V)
- Current: 10 mA
SKU: n/a -
Power Supply
TEKTRONIX 1011A
POWER SUPPLY.
The 1101A has two power receptacles that will power up to two independent probes.
The 1101A is a power supply provides external power to probes when the oscilloscope used does not have the capability to supply probe power.Two external probe power supplies
87-128/174-250 Vac; 48-440 Hz operation
Selectable 50 ohm, termination for use with 50 Ohm or 1 Mohm inputs
Overload protected
Variable DC offset, up to ±200 V
Compatible with the P6201, P6202A and P6230SKU: n/a -
Power Supply
SORENSEN DCS8-125
Programmable POWER SUPPLY 0-8 VOLTS 0-125 AMPS.
he DCS80-125 is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 8V and 125A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
DatasheetSKU: n/a -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
DatasheetSKU: n/a -
Power Supply
METAF MCP M10-QR305 2x30V/5A 5V/1A DC Linear Adjustable Power Supply
The MCP M10-QR305 2x30V/5A 5V/1A DC Linear Adjustable Power Supply is a equipment with high stability, high reliability, low noise, its output voltage or current can be continuously adjusted, and its constant voltage and current can auto-conversion. This low cost and universal power supply can be used in many different areas, from test of R&D equipment to test of production lines.
Features:
– Output off function
– Triple independent DC outputs. Two adjustable and one fixed output
– Independent, series and parallel variety output
– Constant voltage and constant current
– Low ripple and noise
– Four LED displays with 3 digits, selectable for two sets output voltage and current display simultaneously
– 16 hours continuous output with full load
– Auto tracking outputIndependent output:
CH1: 0-30V/0-05A
CH2: 0-30V/0-05A
CH3: 5V/1ASerial output:
CH1+CH2: 0-60V/0-5AParallel output:
CH1+CH2: 0-30V/0-10ASpecification:
Line Regulation: CV 1X10^-4+3mV CC 2X10^-3+3mA CH3 5mV
Load Regulation: CV 1X10^-4+4mV CC 2X10^-3+3mA CH3 15mV
Ripple & Noise: CV 1mVrms CC 3mA rms CH3 2mV
Display Accuracy: ±(0.5%Rdg+2digits)
Input Voltage: 110~127VAC±10%, 220~240VAC±10%
Dimensions (L x W x D): 250x135x460mm
Weight: 8,2 kgSKU: n/a -
Power Supply
METAF HPS305D
Metaf HPS305D is a Single-channel direct current (0 – 5 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
DatasheetSKU: n/a€130.00 View Product -
Power Supply
METAF HPS3010D
Metaf HPS3010D is a Single-channel direct current (0 – 10 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
DatasheetSKU: n/a€140.00 View Product
-
Power Supply
RIGOL DP932A
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/O -
Power Supply
RIGOL DP2031
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 5 A, DC, max 222 W). 4.3-inch LCD color touch screen. High resolution for measurement of 1 μA low range current. Low output ripple and noise <350 μVrms/2 mVpp. USB HOST, LAN, Digital I/O, and RS232 (standard)
3 electrically isolated independent channels with a maximum total power of up to 222 W
32 V/3 A || 32 V/3 A || 6 V/5 A (standard)
32 V/2 A || 32 V/2 A || 6 V/10 A (optional)
4.3-inch LCD color touch screen
Internal series/parallel connections for CH1 and CH2
High resolution for measurement of 1 μA low range current
Capability to measure and display wide dynamic ranges of current
Excellent programming/readback accuracy
Transient response time <50 μs
Front and rear output terminals
2-wire or 4-wire remote sense
A maximum of 512 arbitrary points with dwell time down to 1 ms; various built-in basic waveforms
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Automatic switchover between low and high range measurement
Timing output, energy consumption analysis (IoT), data logging and analysis
Capability to measure the minimum of 1 ms pulse current
Three rack-units (3U), 1/2-rack form factor
Software control
Over voltage, over current, and over temperature protection
Various interfaces available: USB HOST, LAN, Digital I/O, and RS232 (standard) -
Power Supply
RIGOL DP932U
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/O -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions. -
Power Supply
RIGOL DP932E
The DP900 Series Power Supplies combine our new touch screen interface with new flexibility and higher speed functions designed for benchtop DC power analysis. The DP932A and DP932U are 3 channel completely isolated benchtop power supplies. Activate the high-speed arb function that allows you to update the power supply output at up to 10 times per second while quickly creating a repeating shape or pattern from the front panel. You can also combine channels 1 and 2 internally either in parallel or in series to expand the power envelope for your testing. No more cabling challenges since you can now get the current or voltage for both channels with one cable connection. The DP932A comes with all the capabilities enabled. The DP932U has optional resolution, digital IO, and arbitrary speed upgrades. The DP932U also comes with safety banana plugs in place of the binding posts on the DP932A. This combination of flexibility and capability makes the DP900 an important addition to any engineer’s bench.
-
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
-
Power Supply
AGILENT-Hp/Keysight E3631A
The triple output, 80 W, GPIB, E3631A provides small, compact size for bench use; low output ripple and noise; built-in measurements and basic programmable features with GPIB and RS232 interface. This clean and reliable supply is designed for general purpose applications; and combines convenient benchtop capabilities with flexible system features in a compact, multi-output package.
Output 1: 0 to 6 V, 0 to 5 A
Output 2: 0 to +25 V, 0 to 1 A
Output 3: 0 to -25 V, 0 to 1 A
Programming Accuracy at 25°C ±5°C
Voltage: 0.05% + 20 mV, 0.05% + 20 mV, 0.1% + 5 mV
+ Current: 0.15% + 4 mA, 0.15% + 4 mA, 0.2% + 10 mA
Normal Mode Voltage: <350 µVrms/ 2 mV p-p, <350 µV rms/2 mV p-p, <350 µV rms/2 mV p-p Normal-mode current: <500 µA rms, <500 µA rms, <2 mA rms Common-mode current: <1.5 µA rms, <1.5 µA rms, <1.5 µA rms Readback Accuracy at 25°C ±5° 1200W, DC System Power Supplies,60V - 50A. Datasheet -
Power Supply
HP-Agilent/Keysight 6012B
These single-output supplies can replace multiple units, saving rack space and reducing system cost and complexity.
Autoranging outputs provide maximum power at a variety of operating points
Overvoltage features protect DUTs quickly and automatically
Auto-parallel or auto-series connections enable greater output flexibility
Ten-turn pots for precise local control1200W, DC System Power Supplies,60V – 50A.
Datasheet -
Power Supply
AGILENT-Hp/Keysight N5748A
Output Ratings
Voltage: 80 V
Current: 9.5 A
Power: 760 WThe single output, 760W N5748A, provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers reliable performance and enhanced capabilities in a compact 1U package.
-
Power Supply
KEYSIGHT – Agilent/Hp N8740A
Keysight's basic DC power supplies offer essential features for a tight budget. The Keysight N8740A is a 150 V, 22 A, 3300 W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
Please select the AC input voltage option carefully. The AC input voltage hardware is permanently installed at the factory and cannot be changed under any circumstances after delivery. If the wrong AC input voltage option is purchased and delivered, the unit would need to be returned. Product returns are subject to Keysight approval and applicable charges. A new order would then have to be placed.
DC output ratingsVoltage: 150 V
Current: 22 A
Power: 3300 WProgramming accuracy
Voltage: 0.05% + 75 mV
Current: 0.1% + 44 mAOutput ripple and noise
CV p-p: 100 mV
CV rms: 25 mV
Datasheet -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
Datasheet -
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
Datasheet -
Power Supply
AGILENT-Hp/Keysight 6675A
Output Ratings
Output voltage: 0 to 120 V
Output current (40°C): 0 to 18 AProgramming Accuracy at 25°C ±5°C
Voltage 0.04% + 120 mV
Current 0.1% + 12 mARipple & Noise from 20 Hz to 20 MHz
Voltage rms: 1.9 mV
Peak-to-Peak: 16 mV
Current rms: 12 mAHp high performance DC power supplies offer speed and accuracy for test optimization. The single output, 2000 W GPIB 6671A-6675A provide fast, low-noise outputs; analog control of output voltage and current; and fan-speed control to minimize acoustic noise.
The Hp 2160W, GPIB, single output 6675A is a highly efficient low-noise supply that maximize test throughput and is designed to offer excellent reliability, low ripple and noise, and extremely accurate built-in measurements of voltage and current.
Datasheet -
Power Supply
ELIND 3232
Electronic linear laboratory bench power supply model ELIND 328. Suitable for professional use. Adjustable in voltage and current: 0-32V and 0-3.2A continuous (DC). Outputs isolated from the ground (can therefore also be used with the positive to ground). Multiturn knob for fine tension adjustment. Tool to monitor voltage or current. Excellent condition. Used very little. Dimensions: 14.5×9.5x25cm. Weight 2Kg. 220V AC cable power supply
-
Power Supply
AGILENT-Hp/Keysight 6645A
Questa serie di alimentatori CC regolati lineari da 200 W è progettata per massimizzare la produttività dei DUT attraverso il processo di test di produzione con tempi di programmazione rapidi su e giù.
I preziosi insiemi possono essere distrutti da un guasto minore di un componente che può consentire un flusso di tensione o corrente che fluisce verso il DUT. Le funzioni di protezione rapida, tra cui il piede di porco rapido, la protezione crossover in modalità e la possibilità di collegare i circuiti di protezione di più alimentatori possono aumentare il rendimento di produzione.
La programmazione dell'uscita CC e delle funzioni di protezione può essere effettuata dal pannello frontale o utilizzando i comandi SCPI standard del settore, tramite GPIB. Utilizzando il collegamento seriale, è possibile collegare fino a 16 alimentatori tramite un indirizzo GPIB. L'integrazione del sistema di test può essere ulteriormente semplificata utilizzando i driver VXIplug & play. La tensione e la corrente di uscita possono anche essere controllate con segnali analogici. Ciò è utile per alcuni tipi di ambienti rumorosi e anche per reazioni immediate ai cambiamenti di processo.Tensione flottante CC: i terminali di uscita possono essere fatti galleggiare fino a ± 240 V CC dalla terra del telaio.
Telerilevamento: è possibile far cadere fino a metà della tensione di uscita nominale in ciascun cavo di carico. La caduta del carico comporta la sottrazione della tensione disponibile per il carico.
Tempo di elaborazione del comando: il tempo medio necessario affinché la tensione di uscita inizi a cambiare in seguito alla ricezione di dati digitali è di 20 ms per gli alimentatori collegati direttamente al GPIB.
Tempo di risposta della programmazione dell'uscita: il tempo di salita e discesa (10/90% e 90/10%) della tensione di uscita è inferiore a 15 ms. La variazione della tensione di uscita si assesta entro 1 LSB (0,025% x tensione nominale) del valore finale in meno di 60 ms.
Programmazione verso il basso: un programmatore attivo verso il basso affonda circa il 20% della corrente di uscita nominale.Valori nominali di uscita
Tensione di uscita: da 0 a 120 V.
Corrente di uscita (40 ° C): da 0 a 1,5 A
Corrente massima (50 ° C / 55 ° C): 1,4 A / 1,3 APrecisione di programmazione a 25 ° C ± 5 ° C
Tensione 0,06% + 51 mV
Corrente 0,15% + 1,7 mARipple & Noise (20 Hz – 20 MHz)
Voltaggio rms: 700 µV
Tensione picco-picco: 7 mV
Corrente efficace: 1 mA
Scheda Tecnica -
Power Supply
HP-Agilent/Keysight 6645A
HP high performance DC power supplies offer speed and accuracy for test optimization. The single output, 200 W, GPIB 6641A-6645A provide fast, low-noise outputs; analog control of output voltage and current; fan-speed control to minimize acoustic noise; as well as parallel and series connections of multiple units.
The HP 180W, GPIB, single output 6645A is a versatile programmable supply designed to maximize test throughput during design verification or on the production line, and is fully programmable to help reduce test time through a variety of automated capabilities.
Output Ratings
Output voltage: 0 to 120 V
Output current (40° C): 0 to 1.5 A
Maximum current (50° C/55° C): 1.4 A/1.3 AProgramming Accuracy at 25°C ±5°C
Voltage 0.06% + 51 mV
Current 0.15% + 1.7 mARipple & Noise (20 Hz – 20 MHz)
Voltage rms: 700 µV
Voltage peak-to-peak: 7 mV
Current rms: 1 mA
Datasheet -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
Datasheet -
Power Supply
KEYSIGHT N8940A
KEYSIGHT N8940A Alimentatore CC con autoranging, 80 V, 170 A, 5000 W, 400 V CA.
La serie Keysight N8900 offre alimentazione CC programmabile a uscita singola programmabile da 5 kW, 10 kW e 15 kW per applicazioni ATE che richiedono la giusta quantità di prestazioni al giusto prezzo. La caratteristica di uscita a regolazione automatica degli alimentatori serie N8900 consente una flessibilità senza precedenti offrendo una vasta gamma di combinazioni di tensione e corrente a piena potenza. Gli alimentatori con caratteristiche di uscita “rettangolari” o tradizionali forniscono piena potenza con una sola combinazione di tensione e corrente. Solo un N8900 fa il lavoro di più alimentatori. È come avere molti alimentatori in uno!
La serie N8900 offre potenza di uscita stabile, misurazioni di tensione e corrente incorporate e tensione e corrente di uscita con autorangolazione da 80 V a 1500 V e da 10 A a 510 A. Questi alimentatori offrono molte funzionalità pronte per il sistema come interfacce I / O standard multiple per semplificare e accelerare lo sviluppo del sistema di test e il design compatto 3U per risparmiare spazio nel rack. Se è necessaria più potenza, è possibile mettere in parallelo più unità N8900 per creare un “unico” alimentatore con> 100 kW di potenza totale in uscita. Il controllo master / slave incorporato consente la programmazione come se fosse solo un grande alimentatore; non è necessario programmare ciascuna fornitura singolarmente.Uscita autoranging – fa il lavoro di più alimentatori!
Potenza di uscita massima di 5 kW, 10 kW e 15 kW
Fino a 1500 V e fino a 510 A
14 diverse combinazioni di tensione, corrente e potenza disponibili in 208 V CA o 400 V CA (28 modelli in totale)
La giusta quantità di prestazioni al giusto prezzo
Unità facilmente parallele per creare un “unico” alimentatore con> 100 kW di potenza
Misura di tensione e corrente incorporata
Alta densità di potenza, 15 kW in soli 3U (5,25 “/ 13,34 cm)
Protezione da sovratensione, sovracorrente e sovratemperatura
Interfacce LAN (LXI Core), USB, GPIB e analogiche tutte standardValori nominali DC
Voltaggio: da 0 a 80 V.
Corrente: da 0 a 170 A
Potenza: 5000 W.Ingresso AC
Intervallo di tensione: 360-440 V CA.
Accuratezza della programmazione
Tensione: 0,1% del fondo scala
Corrente: 0,2% del fondo scala
Scheda Tecnica -
Power Supply
H10S CLT-100
Exclusive power supply is required for DC screwdrivers.
● Exclusive power supply converts the electric current from AC outlet (on the primary side) to low-voltage output (HI: DC30V) or (LOW: about DC20V) to supply it to the screwdriver.
● Safe and quiet rotation.
● Please always use HIOS screwdriver in combination with HIOS power supply for safe screw tightening.
● Stable power supply with multiple inputs (AC100V to 240V).
(Not applicable to CLT-100 and MC-70L) -
Power Supply
HP/AGILENT/KEYSIGHT E3615A
HP basic DC power supplies offer essential features for a tight budget. The single output, 30-60 W, E3610A-E3617A provide small, compact size for bench use; low-noise and excellent regulation; and dual-range outputs (E3610A/11A/12A). The HP 60W, single output E3615A is a reliable and convenient power for benchtop use, and offers solid performance and a variety of basic and enhanced capabilities.
The E3600 Series of low-cost benchtop power supplies give you the performance of system power supplies at a decent price. All E3600 family members provide clean power with excellent regulation and a fast transient response. The E3600 Series single-output non-programmable models are described on this page. Refer to page 3 for information on dual-output and triple-output non- programmable models.
All E3600 Series single-output non-programmable power supplies feature separate digital-panel meters for monitoring voltage and current simultaneously, giving you precise reading and control capability. All models also feature 10-turn potentiometers for accurate adjustment of voltage and current output settings.
With 0.01 percent load and line regulation, these instruments keep the output steady when power line and load changes occur.
The low normal mode noise specification of less than 200 μVrms ensures clean power for precision circuitry.In all single-output models, either the positive or negative terminal can be connected to ground, providing a positive or negative voltage output. Outputs can also be floated up to 240 V from ground.
These instruments also feature adjustable current limits, letting you set the safest current limit without having to short the output.
These popular 30-watt bench supplies are designed for general laboratory use. The constant-voltage, constant-current output allows operation as either a voltage or current source. The changeover occurs automatically, based on the load. Each of these models has two ranges, allowing more current at a lower voltage. For higher output voltages, supplies can be connected in series. These models also feature overload protection. A continuously acting constant current curcuit protects the power supply against all overloads including a direct short placed across the terminals in a constant voltage operation.
These fexible 60-watt, single-range power supplies can be used as either voltage or current sources. When the output terminal voltage increases to a preset shut-down level, an overvoltage protection circuit disables the output to protect the device under test (DUT) for damage. The overvoltage protection feature can be easily monitored and adjusted from the front panel.
Using the remote sensing capability, these instruments automatically compensate for voltage drop in the load leads, so you obtain an accurate voltage at the DUT.
Using the remote analog voltage programming capability, these instruments can remotely vary the voltage, so you are able to control the regulation output voltage or current.
Output Ratings (Maximum current is derated 1% per °C between 40° to 55°C)
- Range 1: 0 to 20 V, 0 to 3 A
- Range 2: NA
- Power (max): 60 W
Ripple & Noise from 20 Hz to 20 MHz
- Voltage rms: 200 µV
- Peak-to-Peak: 1 mV
Load & Line Regulation
- 0.01% + 2 mV
Meter Resolution
- Voltage: 10 mV (0-20 V), 100 mV (>20 V)
- Current: 10 mA
-
Power Supply
TEKTRONIX 1011A
POWER SUPPLY.
The 1101A has two power receptacles that will power up to two independent probes.
The 1101A is a power supply provides external power to probes when the oscilloscope used does not have the capability to supply probe power.Two external probe power supplies
87-128/174-250 Vac; 48-440 Hz operation
Selectable 50 ohm, termination for use with 50 Ohm or 1 Mohm inputs
Overload protected
Variable DC offset, up to ±200 V
Compatible with the P6201, P6202A and P6230 -
Power Supply
SORENSEN DCS8-125
Programmable POWER SUPPLY 0-8 VOLTS 0-125 AMPS.
he DCS80-125 is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 8V and 125A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Supply
METAF MCP M10-QR305 2x30V/5A 5V/1A DC Linear Adjustable Power Supply
The MCP M10-QR305 2x30V/5A 5V/1A DC Linear Adjustable Power Supply is a equipment with high stability, high reliability, low noise, its output voltage or current can be continuously adjusted, and its constant voltage and current can auto-conversion. This low cost and universal power supply can be used in many different areas, from test of R&D equipment to test of production lines.
Features:
– Output off function
– Triple independent DC outputs. Two adjustable and one fixed output
– Independent, series and parallel variety output
– Constant voltage and constant current
– Low ripple and noise
– Four LED displays with 3 digits, selectable for two sets output voltage and current display simultaneously
– 16 hours continuous output with full load
– Auto tracking outputIndependent output:
CH1: 0-30V/0-05A
CH2: 0-30V/0-05A
CH3: 5V/1ASerial output:
CH1+CH2: 0-60V/0-5AParallel output:
CH1+CH2: 0-30V/0-10ASpecification:
Line Regulation: CV 1X10^-4+3mV CC 2X10^-3+3mA CH3 5mV
Load Regulation: CV 1X10^-4+4mV CC 2X10^-3+3mA CH3 15mV
Ripple & Noise: CV 1mVrms CC 3mA rms CH3 2mV
Display Accuracy: ±(0.5%Rdg+2digits)
Input Voltage: 110~127VAC±10%, 220~240VAC±10%
Dimensions (L x W x D): 250x135x460mm
Weight: 8,2 kg -
Power Supply
METAF HPS305D
Metaf HPS305D is a Single-channel direct current (0 – 5 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet -
Power Supply
METAF HPS3010D
Metaf HPS3010D is a Single-channel direct current (0 – 10 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet
-
Power Supply
RIGOL DP932A
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/O€690.00 View Product -
Power Supply
RIGOL DP2031
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 5 A, DC, max 222 W). 4.3-inch LCD color touch screen. High resolution for measurement of 1 μA low range current. Low output ripple and noise <350 μVrms/2 mVpp. USB HOST, LAN, Digital I/O, and RS232 (standard)
3 electrically isolated independent channels with a maximum total power of up to 222 W
32 V/3 A || 32 V/3 A || 6 V/5 A (standard)
32 V/2 A || 32 V/2 A || 6 V/10 A (optional)
4.3-inch LCD color touch screen
Internal series/parallel connections for CH1 and CH2
High resolution for measurement of 1 μA low range current
Capability to measure and display wide dynamic ranges of current
Excellent programming/readback accuracy
Transient response time <50 μs
Front and rear output terminals
2-wire or 4-wire remote sense
A maximum of 512 arbitrary points with dwell time down to 1 ms; various built-in basic waveforms
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Automatic switchover between low and high range measurement
Timing output, energy consumption analysis (IoT), data logging and analysis
Capability to measure the minimum of 1 ms pulse current
Three rack-units (3U), 1/2-rack form factor
Software control
Over voltage, over current, and over temperature protection
Various interfaces available: USB HOST, LAN, Digital I/O, and RS232 (standard)€1,099.00 View Product -
Power Supply
RIGOL DP932U
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/O€529.00 View Product -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions.€599.00 View Product -
Power Supply
RIGOL DP932E
The DP900 Series Power Supplies combine our new touch screen interface with new flexibility and higher speed functions designed for benchtop DC power analysis. The DP932A and DP932U are 3 channel completely isolated benchtop power supplies. Activate the high-speed arb function that allows you to update the power supply output at up to 10 times per second while quickly creating a repeating shape or pattern from the front panel. You can also combine channels 1 and 2 internally either in parallel or in series to expand the power envelope for your testing. No more cabling challenges since you can now get the current or voltage for both channels with one cable connection. The DP932A comes with all the capabilities enabled. The DP932U has optional resolution, digital IO, and arbitrary speed upgrades. The DP932U also comes with safety banana plugs in place of the binding posts on the DP932A. This combination of flexibility and capability makes the DP900 an important addition to any engineer’s bench.
€425.00 View Product -
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
€589.00 View Product -
Power Supply
AGILENT-Hp/Keysight E3631A
The triple output, 80 W, GPIB, E3631A provides small, compact size for bench use; low output ripple and noise; built-in measurements and basic programmable features with GPIB and RS232 interface. This clean and reliable supply is designed for general purpose applications; and combines convenient benchtop capabilities with flexible system features in a compact, multi-output package.
Output 1: 0 to 6 V, 0 to 5 A
Output 2: 0 to +25 V, 0 to 1 A
Output 3: 0 to -25 V, 0 to 1 A
Programming Accuracy at 25°C ±5°C
Voltage: 0.05% + 20 mV, 0.05% + 20 mV, 0.1% + 5 mV
+ Current: 0.15% + 4 mA, 0.15% + 4 mA, 0.2% + 10 mA
Normal Mode Voltage: <350 µVrms/ 2 mV p-p, <350 µV rms/2 mV p-p, <350 µV rms/2 mV p-p Normal-mode current: <500 µA rms, <500 µA rms, <2 mA rms Common-mode current: <1.5 µA rms, <1.5 µA rms, <1.5 µA rms Readback Accuracy at 25°C ±5° 1200W, DC System Power Supplies,60V - 50A. Datasheet -
Power Supply
HP-Agilent/Keysight 6012B
These single-output supplies can replace multiple units, saving rack space and reducing system cost and complexity.
Autoranging outputs provide maximum power at a variety of operating points
Overvoltage features protect DUTs quickly and automatically
Auto-parallel or auto-series connections enable greater output flexibility
Ten-turn pots for precise local control1200W, DC System Power Supplies,60V – 50A.
Datasheet -
Power Supply
AGILENT-Hp/Keysight N5748A
Output Ratings
Voltage: 80 V
Current: 9.5 A
Power: 760 WThe single output, 760W N5748A, provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers reliable performance and enhanced capabilities in a compact 1U package.
-
Power Supply
KEYSIGHT – Agilent/Hp N8740A
Keysight's basic DC power supplies offer essential features for a tight budget. The Keysight N8740A is a 150 V, 22 A, 3300 W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
Please select the AC input voltage option carefully. The AC input voltage hardware is permanently installed at the factory and cannot be changed under any circumstances after delivery. If the wrong AC input voltage option is purchased and delivered, the unit would need to be returned. Product returns are subject to Keysight approval and applicable charges. A new order would then have to be placed.
DC output ratingsVoltage: 150 V
Current: 22 A
Power: 3300 WProgramming accuracy
Voltage: 0.05% + 75 mV
Current: 0.1% + 44 mAOutput ripple and noise
CV p-p: 100 mV
CV rms: 25 mV
Datasheet -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
Datasheet€729.00 View Product -
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
Datasheet€710.00 View Product -
Power Supply
AGILENT-Hp/Keysight 6675A
Output Ratings
Output voltage: 0 to 120 V
Output current (40°C): 0 to 18 AProgramming Accuracy at 25°C ±5°C
Voltage 0.04% + 120 mV
Current 0.1% + 12 mARipple & Noise from 20 Hz to 20 MHz
Voltage rms: 1.9 mV
Peak-to-Peak: 16 mV
Current rms: 12 mAHp high performance DC power supplies offer speed and accuracy for test optimization. The single output, 2000 W GPIB 6671A-6675A provide fast, low-noise outputs; analog control of output voltage and current; and fan-speed control to minimize acoustic noise.
The Hp 2160W, GPIB, single output 6675A is a highly efficient low-noise supply that maximize test throughput and is designed to offer excellent reliability, low ripple and noise, and extremely accurate built-in measurements of voltage and current.
Datasheet -
Power Supply
ELIND 3232
Electronic linear laboratory bench power supply model ELIND 328. Suitable for professional use. Adjustable in voltage and current: 0-32V and 0-3.2A continuous (DC). Outputs isolated from the ground (can therefore also be used with the positive to ground). Multiturn knob for fine tension adjustment. Tool to monitor voltage or current. Excellent condition. Used very little. Dimensions: 14.5×9.5x25cm. Weight 2Kg. 220V AC cable power supply
-
Power Supply
AGILENT-Hp/Keysight 6645A
Questa serie di alimentatori CC regolati lineari da 200 W è progettata per massimizzare la produttività dei DUT attraverso il processo di test di produzione con tempi di programmazione rapidi su e giù.
I preziosi insiemi possono essere distrutti da un guasto minore di un componente che può consentire un flusso di tensione o corrente che fluisce verso il DUT. Le funzioni di protezione rapida, tra cui il piede di porco rapido, la protezione crossover in modalità e la possibilità di collegare i circuiti di protezione di più alimentatori possono aumentare il rendimento di produzione.
La programmazione dell'uscita CC e delle funzioni di protezione può essere effettuata dal pannello frontale o utilizzando i comandi SCPI standard del settore, tramite GPIB. Utilizzando il collegamento seriale, è possibile collegare fino a 16 alimentatori tramite un indirizzo GPIB. L'integrazione del sistema di test può essere ulteriormente semplificata utilizzando i driver VXIplug & play. La tensione e la corrente di uscita possono anche essere controllate con segnali analogici. Ciò è utile per alcuni tipi di ambienti rumorosi e anche per reazioni immediate ai cambiamenti di processo.Tensione flottante CC: i terminali di uscita possono essere fatti galleggiare fino a ± 240 V CC dalla terra del telaio.
Telerilevamento: è possibile far cadere fino a metà della tensione di uscita nominale in ciascun cavo di carico. La caduta del carico comporta la sottrazione della tensione disponibile per il carico.
Tempo di elaborazione del comando: il tempo medio necessario affinché la tensione di uscita inizi a cambiare in seguito alla ricezione di dati digitali è di 20 ms per gli alimentatori collegati direttamente al GPIB.
Tempo di risposta della programmazione dell'uscita: il tempo di salita e discesa (10/90% e 90/10%) della tensione di uscita è inferiore a 15 ms. La variazione della tensione di uscita si assesta entro 1 LSB (0,025% x tensione nominale) del valore finale in meno di 60 ms.
Programmazione verso il basso: un programmatore attivo verso il basso affonda circa il 20% della corrente di uscita nominale.Valori nominali di uscita
Tensione di uscita: da 0 a 120 V.
Corrente di uscita (40 ° C): da 0 a 1,5 A
Corrente massima (50 ° C / 55 ° C): 1,4 A / 1,3 APrecisione di programmazione a 25 ° C ± 5 ° C
Tensione 0,06% + 51 mV
Corrente 0,15% + 1,7 mARipple & Noise (20 Hz – 20 MHz)
Voltaggio rms: 700 µV
Tensione picco-picco: 7 mV
Corrente efficace: 1 mA
Scheda Tecnica -
Power Supply
HP-Agilent/Keysight 6645A
HP high performance DC power supplies offer speed and accuracy for test optimization. The single output, 200 W, GPIB 6641A-6645A provide fast, low-noise outputs; analog control of output voltage and current; fan-speed control to minimize acoustic noise; as well as parallel and series connections of multiple units.
The HP 180W, GPIB, single output 6645A is a versatile programmable supply designed to maximize test throughput during design verification or on the production line, and is fully programmable to help reduce test time through a variety of automated capabilities.
Output Ratings
Output voltage: 0 to 120 V
Output current (40° C): 0 to 1.5 A
Maximum current (50° C/55° C): 1.4 A/1.3 AProgramming Accuracy at 25°C ±5°C
Voltage 0.06% + 51 mV
Current 0.15% + 1.7 mARipple & Noise (20 Hz – 20 MHz)
Voltage rms: 700 µV
Voltage peak-to-peak: 7 mV
Current rms: 1 mA
Datasheet -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
Datasheet -
Power Supply
KEYSIGHT N8940A
KEYSIGHT N8940A Alimentatore CC con autoranging, 80 V, 170 A, 5000 W, 400 V CA.
La serie Keysight N8900 offre alimentazione CC programmabile a uscita singola programmabile da 5 kW, 10 kW e 15 kW per applicazioni ATE che richiedono la giusta quantità di prestazioni al giusto prezzo. La caratteristica di uscita a regolazione automatica degli alimentatori serie N8900 consente una flessibilità senza precedenti offrendo una vasta gamma di combinazioni di tensione e corrente a piena potenza. Gli alimentatori con caratteristiche di uscita “rettangolari” o tradizionali forniscono piena potenza con una sola combinazione di tensione e corrente. Solo un N8900 fa il lavoro di più alimentatori. È come avere molti alimentatori in uno!
La serie N8900 offre potenza di uscita stabile, misurazioni di tensione e corrente incorporate e tensione e corrente di uscita con autorangolazione da 80 V a 1500 V e da 10 A a 510 A. Questi alimentatori offrono molte funzionalità pronte per il sistema come interfacce I / O standard multiple per semplificare e accelerare lo sviluppo del sistema di test e il design compatto 3U per risparmiare spazio nel rack. Se è necessaria più potenza, è possibile mettere in parallelo più unità N8900 per creare un “unico” alimentatore con> 100 kW di potenza totale in uscita. Il controllo master / slave incorporato consente la programmazione come se fosse solo un grande alimentatore; non è necessario programmare ciascuna fornitura singolarmente.Uscita autoranging – fa il lavoro di più alimentatori!
Potenza di uscita massima di 5 kW, 10 kW e 15 kW
Fino a 1500 V e fino a 510 A
14 diverse combinazioni di tensione, corrente e potenza disponibili in 208 V CA o 400 V CA (28 modelli in totale)
La giusta quantità di prestazioni al giusto prezzo
Unità facilmente parallele per creare un “unico” alimentatore con> 100 kW di potenza
Misura di tensione e corrente incorporata
Alta densità di potenza, 15 kW in soli 3U (5,25 “/ 13,34 cm)
Protezione da sovratensione, sovracorrente e sovratemperatura
Interfacce LAN (LXI Core), USB, GPIB e analogiche tutte standardValori nominali DC
Voltaggio: da 0 a 80 V.
Corrente: da 0 a 170 A
Potenza: 5000 W.Ingresso AC
Intervallo di tensione: 360-440 V CA.
Accuratezza della programmazione
Tensione: 0,1% del fondo scala
Corrente: 0,2% del fondo scala
Scheda Tecnica -
Power Supply
H10S CLT-100
Exclusive power supply is required for DC screwdrivers.
● Exclusive power supply converts the electric current from AC outlet (on the primary side) to low-voltage output (HI: DC30V) or (LOW: about DC20V) to supply it to the screwdriver.
● Safe and quiet rotation.
● Please always use HIOS screwdriver in combination with HIOS power supply for safe screw tightening.
● Stable power supply with multiple inputs (AC100V to 240V).
(Not applicable to CLT-100 and MC-70L)€120.00 View Product -
Power Supply
HP/AGILENT/KEYSIGHT E3615A
HP basic DC power supplies offer essential features for a tight budget. The single output, 30-60 W, E3610A-E3617A provide small, compact size for bench use; low-noise and excellent regulation; and dual-range outputs (E3610A/11A/12A). The HP 60W, single output E3615A is a reliable and convenient power for benchtop use, and offers solid performance and a variety of basic and enhanced capabilities.
The E3600 Series of low-cost benchtop power supplies give you the performance of system power supplies at a decent price. All E3600 family members provide clean power with excellent regulation and a fast transient response. The E3600 Series single-output non-programmable models are described on this page. Refer to page 3 for information on dual-output and triple-output non- programmable models.
All E3600 Series single-output non-programmable power supplies feature separate digital-panel meters for monitoring voltage and current simultaneously, giving you precise reading and control capability. All models also feature 10-turn potentiometers for accurate adjustment of voltage and current output settings.
With 0.01 percent load and line regulation, these instruments keep the output steady when power line and load changes occur.
The low normal mode noise specification of less than 200 μVrms ensures clean power for precision circuitry.In all single-output models, either the positive or negative terminal can be connected to ground, providing a positive or negative voltage output. Outputs can also be floated up to 240 V from ground.
These instruments also feature adjustable current limits, letting you set the safest current limit without having to short the output.
These popular 30-watt bench supplies are designed for general laboratory use. The constant-voltage, constant-current output allows operation as either a voltage or current source. The changeover occurs automatically, based on the load. Each of these models has two ranges, allowing more current at a lower voltage. For higher output voltages, supplies can be connected in series. These models also feature overload protection. A continuously acting constant current curcuit protects the power supply against all overloads including a direct short placed across the terminals in a constant voltage operation.
These fexible 60-watt, single-range power supplies can be used as either voltage or current sources. When the output terminal voltage increases to a preset shut-down level, an overvoltage protection circuit disables the output to protect the device under test (DUT) for damage. The overvoltage protection feature can be easily monitored and adjusted from the front panel.
Using the remote sensing capability, these instruments automatically compensate for voltage drop in the load leads, so you obtain an accurate voltage at the DUT.
Using the remote analog voltage programming capability, these instruments can remotely vary the voltage, so you are able to control the regulation output voltage or current.
Output Ratings (Maximum current is derated 1% per °C between 40° to 55°C)
- Range 1: 0 to 20 V, 0 to 3 A
- Range 2: NA
- Power (max): 60 W
Ripple & Noise from 20 Hz to 20 MHz
- Voltage rms: 200 µV
- Peak-to-Peak: 1 mV
Load & Line Regulation
- 0.01% + 2 mV
Meter Resolution
- Voltage: 10 mV (0-20 V), 100 mV (>20 V)
- Current: 10 mA
-
Power Supply
TEKTRONIX 1011A
POWER SUPPLY.
The 1101A has two power receptacles that will power up to two independent probes.
The 1101A is a power supply provides external power to probes when the oscilloscope used does not have the capability to supply probe power.Two external probe power supplies
87-128/174-250 Vac; 48-440 Hz operation
Selectable 50 ohm, termination for use with 50 Ohm or 1 Mohm inputs
Overload protected
Variable DC offset, up to ±200 V
Compatible with the P6201, P6202A and P6230 -
Power Supply
SORENSEN DCS8-125
Programmable POWER SUPPLY 0-8 VOLTS 0-125 AMPS.
he DCS80-125 is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 8V and 125A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Supply
METAF MCP M10-QR305 2x30V/5A 5V/1A DC Linear Adjustable Power Supply
The MCP M10-QR305 2x30V/5A 5V/1A DC Linear Adjustable Power Supply is a equipment with high stability, high reliability, low noise, its output voltage or current can be continuously adjusted, and its constant voltage and current can auto-conversion. This low cost and universal power supply can be used in many different areas, from test of R&D equipment to test of production lines.
Features:
– Output off function
– Triple independent DC outputs. Two adjustable and one fixed output
– Independent, series and parallel variety output
– Constant voltage and constant current
– Low ripple and noise
– Four LED displays with 3 digits, selectable for two sets output voltage and current display simultaneously
– 16 hours continuous output with full load
– Auto tracking outputIndependent output:
CH1: 0-30V/0-05A
CH2: 0-30V/0-05A
CH3: 5V/1ASerial output:
CH1+CH2: 0-60V/0-5AParallel output:
CH1+CH2: 0-30V/0-10ASpecification:
Line Regulation: CV 1X10^-4+3mV CC 2X10^-3+3mA CH3 5mV
Load Regulation: CV 1X10^-4+4mV CC 2X10^-3+3mA CH3 15mV
Ripple & Noise: CV 1mVrms CC 3mA rms CH3 2mV
Display Accuracy: ±(0.5%Rdg+2digits)
Input Voltage: 110~127VAC±10%, 220~240VAC±10%
Dimensions (L x W x D): 250x135x460mm
Weight: 8,2 kg -
Power Supply
METAF HPS305D
Metaf HPS305D is a Single-channel direct current (0 – 5 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet€130.00 View Product -
Power Supply
METAF HPS3010D
Metaf HPS3010D is a Single-channel direct current (0 – 10 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet€140.00 View Product