ItalianoShop
Showing 901–930 of 1499 results
-
Signal Generator
HP-Agilent/Keysight 83650A
The Agilent 83650A synthesized sweeper is the standard of excellence for applications requiring the high performance and accuracy of a synthesized source and the speed and versatility of a sweep oscillator. Synthesized broadband frequency coverage and precise 1 Hz frequency resolution (Opt 008) are generated by indirect synthesis, enabling the Agilent 83650A to achieve low single-sideband phase noise performance. It delivers excellent harmonic performance with harmonics at least 50 dB below the carrier from 2.0 to 26.5 GHz, and at least 40 dB below the carrier above 26.5 GHz.
Features:
Scan modulation to simulate antenna scan patterns
Accurate fixed and swept frequency offset for two-tone measurement
User flatness correction for leveling at remote points in the test system
General purpose source for use in component test, receiver test and for frequency conversion
Sweep Modes: Step, List, Ramp
Maximum Power: +10 dBm 26.5 GHz
Maximum Power: +2.5 dBm >40 GHz
Power Sweep Range: -20 dBm to maximum power
Phase Noise (50 GHz at 10 KHz): -68 dBc
Max FM Deviation (locked): +/- 8 MHz
DatasheetSKU: n/a -
Pulse Pattern Generator
AGILENT-Hp/Keysight 81101A
The Keysight 81101A 50 MHz single-channel Pulse Generator is the economy, entry-level instrument of the 81100 family. All timing parameters (repetition rate, delay, width and transitions) are variable.
The instrument comprises a PLL oscillator that enables the repetition rate to be kept within 0.01% accuracy.
Double-pulses and pulse bursts are available. All pulses can be triggered externally when the PLL is turned off. Bursts can also be triggered by the internal PLL if it is not in use as the repetition-rate generator. An external width (pulse recovery) mode is available, too.
The selectable 50/1000 Ohm source resistance allows output amplitudes up to 10 or 20 Vpp respectively into a 50 Ohm load.
Single-channel pulse generator
50 MHz, 10 V from 50 Ohm into 50 Ohm
Triggerable / PLL operation selectable
Pulse / burst modes selectable
Variable transition times
BNC outputs, single-ended
DatasheetSKU: n/a -
Signal Generator
HP-Agilent/Keysight 8648B
SIGNAL GENERATOR 100KHZ – 2000MHZ OPT.1E6
The HP/Agilent 8648B is a Synthesized RF Signal Generator with frequency range from 9 kHz to 2000 MHz The unit starts with the basic capabilities of the Agilent HP 8647A, enhances residual FM, level accuracy and phase noise performance, offers optional pulse modulation and high power, and extends the frequency to 2 GHz.
SKU: n/a -
Dummy Load
DICONEX 17-0412V
DICONEX OIL-COOLED RF COAXIAL TERMINATION / DUMMY LOAD, 10kW 50Ω
This equipment is a very professional dummy load suitable for to be used in laboratory, or broadcast network.
Diconex Series Oil-Cooled Terminations are self-contained high-power 50 ohm coaxial transmission line terminations requiring no outside power source or additional equipment.
The units provide accurate, dependable, and practically non-reflective termination for testing and adjusting transmitters under non-radiating conditions.
The loads consist essentially of a cylindrical film type resistor immersed in a dielectric coolant. The resistor, individually selected for its accuracy, is enclosed in a special tapered housing which provides a linear reduction in surge impedance directly proportional to the distance along the resistor.
This produces the uniform, practically reflection-less line termination from DC to 1 GHz.
The dummy load works continuously at 5 Kw and intermittent even at 10 kW (max 3-5 min).
The load has a powerful cooling fan, powered at 220 V and an internal heat exchanger.
Input Connector: 1 5/8 “EIA flange
Conditions: Brand new and unusedSKU: n/a -
Oscillator
HP-Agilent/Keysight 8350B
Sweep generator mainframe
Hewlett Packard 8350B Sweep Oscillator Mainframe, Refurbished Versatile microprocessor-controlled mainframe Single-band, straddle-band and broad band plug-ins Accurate, high resolution, digital displays Five marker with marker D and marker sweep Save/recall 9 complete front panel states 10 mV output power to 26.5 GHz Total HP-IB programmability Compatible with HP Network Analyzers Accepts all HP 83500 series plug-ins Options: 400 – 400 Hz Power Line Frequency Operation 803 – HP 5343A Interface Cables 850 – HP 8410C Source Control Cables 908 – Rack Mount Kit 910 – Rack Flange Kit for Instruments with Front Handles Ordering InformationSKU: 39 -
Antenna Analyzer
ANRITSU S331D
Site Master Handheld Cable and Antenna Analyzer Model S331D covers the 25 MHz to 4000 MHz spectrum. The S331D is designed for installing, provisioning, maintaining, and troubleshooting wireless base station cable and antenna systems.
Features:
Range di Frequenza: 25 MHz to 4 GHz
Misure: Return Loss / VSWR, Cable Loss, Distance-To-Fault (DTF), Optical DTF
Velocità Sweep: 2.5 msec / data point
Accuratezza: > 42 dB corrected directivity
Display: TFT a colori con retro illuminazione regolabile
Calibrazione: OSL, InstaCal, e FlexCal
RF Immunity: Performs accurate measurements in co-located cell sites
Signal Standard List / Cable Standard List: Quickly locates commonly used cables and frequency standards
Trace Overlay: Monitors changes with reference traces over time
Limit Lines: Single and Segmented Limit lines
Lingue supportate: Chinese, English, French, German, Japanese, Spanish
Handheld Software Tools: Downloads traces, creates reports, compares traces, and renames files
DatasheetSKU: 479
-
Signal Generator
HP-Agilent/Keysight 83650A
The Agilent 83650A synthesized sweeper is the standard of excellence for applications requiring the high performance and accuracy of a synthesized source and the speed and versatility of a sweep oscillator. Synthesized broadband frequency coverage and precise 1 Hz frequency resolution (Opt 008) are generated by indirect synthesis, enabling the Agilent 83650A to achieve low single-sideband phase noise performance. It delivers excellent harmonic performance with harmonics at least 50 dB below the carrier from 2.0 to 26.5 GHz, and at least 40 dB below the carrier above 26.5 GHz.
Features:
Scan modulation to simulate antenna scan patterns
Accurate fixed and swept frequency offset for two-tone measurement
User flatness correction for leveling at remote points in the test system
General purpose source for use in component test, receiver test and for frequency conversion
Sweep Modes: Step, List, Ramp
Maximum Power: +10 dBm 26.5 GHz
Maximum Power: +2.5 dBm >40 GHz
Power Sweep Range: -20 dBm to maximum power
Phase Noise (50 GHz at 10 KHz): -68 dBc
Max FM Deviation (locked): +/- 8 MHz
Datasheet -
Pulse Pattern Generator
AGILENT-Hp/Keysight 81101A
The Keysight 81101A 50 MHz single-channel Pulse Generator is the economy, entry-level instrument of the 81100 family. All timing parameters (repetition rate, delay, width and transitions) are variable.
The instrument comprises a PLL oscillator that enables the repetition rate to be kept within 0.01% accuracy.
Double-pulses and pulse bursts are available. All pulses can be triggered externally when the PLL is turned off. Bursts can also be triggered by the internal PLL if it is not in use as the repetition-rate generator. An external width (pulse recovery) mode is available, too.
The selectable 50/1000 Ohm source resistance allows output amplitudes up to 10 or 20 Vpp respectively into a 50 Ohm load.
Single-channel pulse generator
50 MHz, 10 V from 50 Ohm into 50 Ohm
Triggerable / PLL operation selectable
Pulse / burst modes selectable
Variable transition times
BNC outputs, single-ended
Datasheet -
Signal Generator
HP-Agilent/Keysight 8648B
SIGNAL GENERATOR 100KHZ – 2000MHZ OPT.1E6
The HP/Agilent 8648B is a Synthesized RF Signal Generator with frequency range from 9 kHz to 2000 MHz The unit starts with the basic capabilities of the Agilent HP 8647A, enhances residual FM, level accuracy and phase noise performance, offers optional pulse modulation and high power, and extends the frequency to 2 GHz.
-
Dummy Load
DICONEX 17-0412V
DICONEX OIL-COOLED RF COAXIAL TERMINATION / DUMMY LOAD, 10kW 50Ω
This equipment is a very professional dummy load suitable for to be used in laboratory, or broadcast network.
Diconex Series Oil-Cooled Terminations are self-contained high-power 50 ohm coaxial transmission line terminations requiring no outside power source or additional equipment.
The units provide accurate, dependable, and practically non-reflective termination for testing and adjusting transmitters under non-radiating conditions.
The loads consist essentially of a cylindrical film type resistor immersed in a dielectric coolant. The resistor, individually selected for its accuracy, is enclosed in a special tapered housing which provides a linear reduction in surge impedance directly proportional to the distance along the resistor.
This produces the uniform, practically reflection-less line termination from DC to 1 GHz.
The dummy load works continuously at 5 Kw and intermittent even at 10 kW (max 3-5 min).
The load has a powerful cooling fan, powered at 220 V and an internal heat exchanger.
Input Connector: 1 5/8 “EIA flange
Conditions: Brand new and unused -
Oscillator
HP-Agilent/Keysight 8350B
Sweep generator mainframe
Hewlett Packard 8350B Sweep Oscillator Mainframe, Refurbished Versatile microprocessor-controlled mainframe Single-band, straddle-band and broad band plug-ins Accurate, high resolution, digital displays Five marker with marker D and marker sweep Save/recall 9 complete front panel states 10 mV output power to 26.5 GHz Total HP-IB programmability Compatible with HP Network Analyzers Accepts all HP 83500 series plug-ins Options: 400 – 400 Hz Power Line Frequency Operation 803 – HP 5343A Interface Cables 850 – HP 8410C Source Control Cables 908 – Rack Mount Kit 910 – Rack Flange Kit for Instruments with Front Handles Ordering Information -
Antenna Analyzer
ANRITSU S331D
Site Master Handheld Cable and Antenna Analyzer Model S331D covers the 25 MHz to 4000 MHz spectrum. The S331D is designed for installing, provisioning, maintaining, and troubleshooting wireless base station cable and antenna systems.
Features:
Range di Frequenza: 25 MHz to 4 GHz
Misure: Return Loss / VSWR, Cable Loss, Distance-To-Fault (DTF), Optical DTF
Velocità Sweep: 2.5 msec / data point
Accuratezza: > 42 dB corrected directivity
Display: TFT a colori con retro illuminazione regolabile
Calibrazione: OSL, InstaCal, e FlexCal
RF Immunity: Performs accurate measurements in co-located cell sites
Signal Standard List / Cable Standard List: Quickly locates commonly used cables and frequency standards
Trace Overlay: Monitors changes with reference traces over time
Limit Lines: Single and Segmented Limit lines
Lingue supportate: Chinese, English, French, German, Japanese, Spanish
Handheld Software Tools: Downloads traces, creates reports, compares traces, and renames files
Datasheet
-
Signal Generator
HP-Agilent/Keysight 83650A
The Agilent 83650A synthesized sweeper is the standard of excellence for applications requiring the high performance and accuracy of a synthesized source and the speed and versatility of a sweep oscillator. Synthesized broadband frequency coverage and precise 1 Hz frequency resolution (Opt 008) are generated by indirect synthesis, enabling the Agilent 83650A to achieve low single-sideband phase noise performance. It delivers excellent harmonic performance with harmonics at least 50 dB below the carrier from 2.0 to 26.5 GHz, and at least 40 dB below the carrier above 26.5 GHz.
Features:
Scan modulation to simulate antenna scan patterns
Accurate fixed and swept frequency offset for two-tone measurement
User flatness correction for leveling at remote points in the test system
General purpose source for use in component test, receiver test and for frequency conversion
Sweep Modes: Step, List, Ramp
Maximum Power: +10 dBm 26.5 GHz
Maximum Power: +2.5 dBm >40 GHz
Power Sweep Range: -20 dBm to maximum power
Phase Noise (50 GHz at 10 KHz): -68 dBc
Max FM Deviation (locked): +/- 8 MHz
Datasheet -
Pulse Pattern Generator
AGILENT-Hp/Keysight 81101A
The Keysight 81101A 50 MHz single-channel Pulse Generator is the economy, entry-level instrument of the 81100 family. All timing parameters (repetition rate, delay, width and transitions) are variable.
The instrument comprises a PLL oscillator that enables the repetition rate to be kept within 0.01% accuracy.
Double-pulses and pulse bursts are available. All pulses can be triggered externally when the PLL is turned off. Bursts can also be triggered by the internal PLL if it is not in use as the repetition-rate generator. An external width (pulse recovery) mode is available, too.
The selectable 50/1000 Ohm source resistance allows output amplitudes up to 10 or 20 Vpp respectively into a 50 Ohm load.
Single-channel pulse generator
50 MHz, 10 V from 50 Ohm into 50 Ohm
Triggerable / PLL operation selectable
Pulse / burst modes selectable
Variable transition times
BNC outputs, single-ended
Datasheet -
Signal Generator
HP-Agilent/Keysight 8648B
SIGNAL GENERATOR 100KHZ – 2000MHZ OPT.1E6
The HP/Agilent 8648B is a Synthesized RF Signal Generator with frequency range from 9 kHz to 2000 MHz The unit starts with the basic capabilities of the Agilent HP 8647A, enhances residual FM, level accuracy and phase noise performance, offers optional pulse modulation and high power, and extends the frequency to 2 GHz.
-
Dummy Load
DICONEX 17-0412V
DICONEX OIL-COOLED RF COAXIAL TERMINATION / DUMMY LOAD, 10kW 50Ω
This equipment is a very professional dummy load suitable for to be used in laboratory, or broadcast network.
Diconex Series Oil-Cooled Terminations are self-contained high-power 50 ohm coaxial transmission line terminations requiring no outside power source or additional equipment.
The units provide accurate, dependable, and practically non-reflective termination for testing and adjusting transmitters under non-radiating conditions.
The loads consist essentially of a cylindrical film type resistor immersed in a dielectric coolant. The resistor, individually selected for its accuracy, is enclosed in a special tapered housing which provides a linear reduction in surge impedance directly proportional to the distance along the resistor.
This produces the uniform, practically reflection-less line termination from DC to 1 GHz.
The dummy load works continuously at 5 Kw and intermittent even at 10 kW (max 3-5 min).
The load has a powerful cooling fan, powered at 220 V and an internal heat exchanger.
Input Connector: 1 5/8 “EIA flange
Conditions: Brand new and unused -
Oscillator
HP-Agilent/Keysight 8350B
Sweep generator mainframe
Hewlett Packard 8350B Sweep Oscillator Mainframe, Refurbished Versatile microprocessor-controlled mainframe Single-band, straddle-band and broad band plug-ins Accurate, high resolution, digital displays Five marker with marker D and marker sweep Save/recall 9 complete front panel states 10 mV output power to 26.5 GHz Total HP-IB programmability Compatible with HP Network Analyzers Accepts all HP 83500 series plug-ins Options: 400 – 400 Hz Power Line Frequency Operation 803 – HP 5343A Interface Cables 850 – HP 8410C Source Control Cables 908 – Rack Mount Kit 910 – Rack Flange Kit for Instruments with Front Handles Ordering Information -
Antenna Analyzer
ANRITSU S331D
Site Master Handheld Cable and Antenna Analyzer Model S331D covers the 25 MHz to 4000 MHz spectrum. The S331D is designed for installing, provisioning, maintaining, and troubleshooting wireless base station cable and antenna systems.
Features:
Range di Frequenza: 25 MHz to 4 GHz
Misure: Return Loss / VSWR, Cable Loss, Distance-To-Fault (DTF), Optical DTF
Velocità Sweep: 2.5 msec / data point
Accuratezza: > 42 dB corrected directivity
Display: TFT a colori con retro illuminazione regolabile
Calibrazione: OSL, InstaCal, e FlexCal
RF Immunity: Performs accurate measurements in co-located cell sites
Signal Standard List / Cable Standard List: Quickly locates commonly used cables and frequency standards
Trace Overlay: Monitors changes with reference traces over time
Limit Lines: Single and Segmented Limit lines
Lingue supportate: Chinese, English, French, German, Japanese, Spanish
Handheld Software Tools: Downloads traces, creates reports, compares traces, and renames files
Datasheet