ItalianoPower Supply
Showing 91–106 of 106 results
-
Power Supply
Rigol DP811
The Rigol DP811 is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 924€464.00 View Product -
Power Supply
Rigol DP811A
The Rigol DP811A is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 738€594.00 View Product -
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
SKU: n/a€564.00 View Product -
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
DatasheetSKU: n/a€694.00 View Product -
Power Supply
RIGOL DP821
The Rigol DP821 is a very high quality programmable laboratory power supply with two switchable outputs (60 V/1 A and 8 V/10 A) and a maximum power output of 140 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP821 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 923€464.00 View Product -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions.SKU: n/a€569.00 View Product -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
DatasheetSKU: n/a€694.00 View Product -
Power Supply
Rigol DP831
The Rigol DP831 is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 922€354.00 View Product -
Power Supply
RIGOL DP831A
The Rigol DP831A is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 441€494.00 View Product -
Power Supply
RIGOL DP932A
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/OSKU: n/a€554.00 View Product -
Power Supply
RIGOL DP932E
The DP900 Series Power Supplies combine our new touch screen interface with new flexibility and higher speed functions designed for benchtop DC power analysis. The DP932A and DP932U are 3 channel completely isolated benchtop power supplies. Activate the high-speed arb function that allows you to update the power supply output at up to 10 times per second while quickly creating a repeating shape or pattern from the front panel. You can also combine channels 1 and 2 internally either in parallel or in series to expand the power envelope for your testing. No more cabling challenges since you can now get the current or voltage for both channels with one cable connection. The DP932A comes with all the capabilities enabled. The DP932U has optional resolution, digital IO, and arbitrary speed upgrades. The DP932U also comes with safety banana plugs in place of the binding posts on the DP932A. This combination of flexibility and capability makes the DP900 an important addition to any engineer’s bench.
SKU: n/a€394.00 View Product -
Power Supply
RIGOL DP932U
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/OSKU: n/a€424.00 View Product -
Power Supply
SORENSEN DCS8-125
Programmable POWER SUPPLY 0-8 VOLTS 0-125 AMPS.
he DCS80-125 is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 8V and 125A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
DatasheetSKU: n/a -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
DatasheetSKU: n/a -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
DatasheetSKU: n/a -
Power Supply
TEKTRONIX 1011A
POWER SUPPLY.
The 1101A has two power receptacles that will power up to two independent probes.
The 1101A is a power supply provides external power to probes when the oscilloscope used does not have the capability to supply probe power.Two external probe power supplies
87-128/174-250 Vac; 48-440 Hz operation
Selectable 50 ohm, termination for use with 50 Ohm or 1 Mohm inputs
Overload protected
Variable DC offset, up to ±200 V
Compatible with the P6201, P6202A and P6230SKU: n/a
-
Power Supply
Rigol DP811
The Rigol DP811 is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply
Rigol DP811A
The Rigol DP811A is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
-
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
Datasheet -
Power Supply
RIGOL DP821
The Rigol DP821 is a very high quality programmable laboratory power supply with two switchable outputs (60 V/1 A and 8 V/10 A) and a maximum power output of 140 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP821 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions. -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
Datasheet -
Power Supply
Rigol DP831
The Rigol DP831 is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply
RIGOL DP831A
The Rigol DP831A is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply
RIGOL DP932A
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/O -
Power Supply
RIGOL DP932E
The DP900 Series Power Supplies combine our new touch screen interface with new flexibility and higher speed functions designed for benchtop DC power analysis. The DP932A and DP932U are 3 channel completely isolated benchtop power supplies. Activate the high-speed arb function that allows you to update the power supply output at up to 10 times per second while quickly creating a repeating shape or pattern from the front panel. You can also combine channels 1 and 2 internally either in parallel or in series to expand the power envelope for your testing. No more cabling challenges since you can now get the current or voltage for both channels with one cable connection. The DP932A comes with all the capabilities enabled. The DP932U has optional resolution, digital IO, and arbitrary speed upgrades. The DP932U also comes with safety banana plugs in place of the binding posts on the DP932A. This combination of flexibility and capability makes the DP900 an important addition to any engineer’s bench.
-
Power Supply
RIGOL DP932U
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/O -
Power Supply
SORENSEN DCS8-125
Programmable POWER SUPPLY 0-8 VOLTS 0-125 AMPS.
he DCS80-125 is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 8V and 125A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
Datasheet -
Power Supply
TEKTRONIX 1011A
POWER SUPPLY.
The 1101A has two power receptacles that will power up to two independent probes.
The 1101A is a power supply provides external power to probes when the oscilloscope used does not have the capability to supply probe power.Two external probe power supplies
87-128/174-250 Vac; 48-440 Hz operation
Selectable 50 ohm, termination for use with 50 Ohm or 1 Mohm inputs
Overload protected
Variable DC offset, up to ±200 V
Compatible with the P6201, P6202A and P6230
-
Power Supply
Rigol DP811
The Rigol DP811 is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€464.00 View Product -
Power Supply
Rigol DP811A
The Rigol DP811A is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€594.00 View Product -
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
€564.00 View Product -
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
Datasheet€694.00 View Product -
Power Supply
RIGOL DP821
The Rigol DP821 is a very high quality programmable laboratory power supply with two switchable outputs (60 V/1 A and 8 V/10 A) and a maximum power output of 140 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP821 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€464.00 View Product -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions.€569.00 View Product -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
Datasheet€694.00 View Product -
Power Supply
Rigol DP831
The Rigol DP831 is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€354.00 View Product -
Power Supply
RIGOL DP831A
The Rigol DP831A is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€494.00 View Product -
Power Supply
RIGOL DP932A
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/O€554.00 View Product -
Power Supply
RIGOL DP932E
The DP900 Series Power Supplies combine our new touch screen interface with new flexibility and higher speed functions designed for benchtop DC power analysis. The DP932A and DP932U are 3 channel completely isolated benchtop power supplies. Activate the high-speed arb function that allows you to update the power supply output at up to 10 times per second while quickly creating a repeating shape or pattern from the front panel. You can also combine channels 1 and 2 internally either in parallel or in series to expand the power envelope for your testing. No more cabling challenges since you can now get the current or voltage for both channels with one cable connection. The DP932A comes with all the capabilities enabled. The DP932U has optional resolution, digital IO, and arbitrary speed upgrades. The DP932U also comes with safety banana plugs in place of the binding posts on the DP932A. This combination of flexibility and capability makes the DP900 an important addition to any engineer’s bench.
€394.00 View Product -
Power Supply
RIGOL DP932U
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 3 A, DC, max 210 W). 4.3-inch LCD color touch screen. Low output ripple and noise <350 μVrms/2 mVpp. Command processing time <10 ms. USB, LAN, and Digital I/O
3 electrically isolated independent channels with a maximum total power of up to 210 W
Voltage / Current CH1: 0 – +32 V / 0 – 3 A
Voltage / Current CH2: 0 – +32 V / 0 – 3 A
Voltage / Current CH3: 0 – +6 V / 0 – 3 A
4.3-inch LCD color touch screen
Front-panel safety sockets available on some models
Internal series/parallel connections for CH1 and CH2
Excellent programming/readback accuracy
Transient response time <50 μs
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Three rack-units (3U), 1/2-rack form factor
PC control
Timing output, data logging and analysis
A maximum of 512 arbitrary points with dwell time down to 100 ms; various built-in basic waveforms
Over voltage, over current, and over temperature protection
Various interfaces available: USB, LAN, and Digital I/O€424.00 View Product -
Power Supply
SORENSEN DCS8-125
Programmable POWER SUPPLY 0-8 VOLTS 0-125 AMPS.
he DCS80-125 is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 8V and 125A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Supply
SORENSEN DCS80-13
Programmable POWER SUPPLY 0-80 VOLTS 0-13 AMPS
The DCS80-13E is a 1000 Watt DC Power Supply from Sorensen. Supplies DC voltage and current to test, design, and troubleshoot electric and electronic circuits.
This unit has a 80V and 13A.
The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilize switch-mode technology to achieve high power density in a low profile chassis. Utilizing unique packaging techniques, the DCS Family provides continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits. This family has 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and overvoltage protection, status and constant-voltage/current mode operation.
The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/ local programming and preview status of voltage, current and OVP setpoints.
Datasheet -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
Datasheet -
Power Supply
TEKTRONIX 1011A
POWER SUPPLY.
The 1101A has two power receptacles that will power up to two independent probes.
The 1101A is a power supply provides external power to probes when the oscilloscope used does not have the capability to supply probe power.Two external probe power supplies
87-128/174-250 Vac; 48-440 Hz operation
Selectable 50 ohm, termination for use with 50 Ohm or 1 Mohm inputs
Overload protected
Variable DC offset, up to ±200 V
Compatible with the P6201, P6202A and P6230