ItalianoModule
Showing all 13 results
-
Module
AGILENT 34903A – 20 Channel Actuator/GP Switch Module for 34970A/34972A
The Agilent 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
* 20 Channel Actuator/GP Switch
* SPDT (Form C) latching relays
* 300 V, 1 A actuation and controlSKU: 1142 -
Module
AGILENT 34907A Multifunction Module for 34970A/34972A
The HP 34907A module for the 34970A/34972A Data Acquisition/Switch Unit allows great flexibility for a variety of sense and control applications. It combines two 8-bit ports of digital input and output, a 100 kHz gated totalizer, and two ±12V analog outputs – all on a single earth-referenced module. The digital inputs and totalizer input may be included in a scan. Alarm limits for the digital and event counter inputs are evaluated continuously, capturing and logging alarm conditions even between scans.
Use the digital outputs with an external power supply to control microwave switches and attenuators, solenoids, power relays, indicators, and more. Use the digital inputs to sense limit switch and digital bus status. There are no complex handshake modes; reads and writes are initiated either from the front panel or the bus.
Count events from devices like photo interrupters, limit switches, and Hall-effect sensors.
It keeps an updated total which can be read via the front panel or programmatically at any time. With 26 bits of resolution, it can count events at full speed for nearly 45 minutes without an overflow.
Use the two electronically calibrated analog outputs to source bias voltages to your device under test, to control your analog programmable power supplies, or use the outputs as setpoints for your control systems. The outputs are programmed directly in volts, either from the front panel or from the bus.
Key Features & Specifications:
– 16 bits of digital input and output
– 100 kHz totalizer input
– Two +/-12V analog outputsSKU: 1145 -
Module
HP-Agilent/Keysight N6731B
Keysight basic modules provide stable output, device protection, and accurate measurements. A single range allows programming voltages and currents from 0 V and 0 A to their maximum voltage and current rating. Use 2-wire local sense or 4-wire remote sense to improve regulation. All modules feature a quick disconnect connector.
Programmable output voltages: 0 to 150 V
Output power: 50 to 300 W
Voltage accuracy: 0.1% + 19 mV (5V output)
Ripple and noise 10 mV (5V output)
Up and down-programming with resistive load typically 20 msOvervoltage, overcurrent, and overtemperature protection
Basic modules are single wide allowing four per mainframe
Modules can operate at lower output power to stay within mainframe rating
Modules include a quick disconnect connector
DatasheetSKU: n/a -
Module
HP-Agilent/Keysight 34905A
The HP 34905A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation.
The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with 2 GHz usable bandwidth, or to the BNC-to-SMB adapters provided with 1 GHz bandwidth. Multiple banks may be cascaded together for applications requiring even larger topologies– create a stubless 16:1 multiplexer in a single frame.
Key Features & Specifications:
– Dual 4 Channel RF Multiplexer
– 2 GHz bandwidth, 50 Ohm
– Cascade together for up to 16:1 multiplexerSKU: 1143 -
Module
HP-Agilent/Keysight 34906A
The HP 34906A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with 2 GHz usable bandwidth, or to the BNC-to-SMB adapters provided with 1 bandwidth. Multiple banks may be cascaded together for applications requiring even larger topologies–create a stubless 16:1 multiplexer in a single frame.
Key Features & Specifications:
– Dual 4 Channel RF Multiplexer
– 2 GHz bandwidth, 75 Ohm
– Cascade together for up to 16:1 multiplexer
– BNC to SMB adapter cables includedSKU: 1144
-
Module
AGILENT 34903A – 20 Channel Actuator/GP Switch Module for 34970A/34972A
The Agilent 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
* 20 Channel Actuator/GP Switch
* SPDT (Form C) latching relays
* 300 V, 1 A actuation and control -
Module
AGILENT 34907A Multifunction Module for 34970A/34972A
The HP 34907A module for the 34970A/34972A Data Acquisition/Switch Unit allows great flexibility for a variety of sense and control applications. It combines two 8-bit ports of digital input and output, a 100 kHz gated totalizer, and two ±12V analog outputs – all on a single earth-referenced module. The digital inputs and totalizer input may be included in a scan. Alarm limits for the digital and event counter inputs are evaluated continuously, capturing and logging alarm conditions even between scans.
Use the digital outputs with an external power supply to control microwave switches and attenuators, solenoids, power relays, indicators, and more. Use the digital inputs to sense limit switch and digital bus status. There are no complex handshake modes; reads and writes are initiated either from the front panel or the bus.
Count events from devices like photo interrupters, limit switches, and Hall-effect sensors.
It keeps an updated total which can be read via the front panel or programmatically at any time. With 26 bits of resolution, it can count events at full speed for nearly 45 minutes without an overflow.
Use the two electronically calibrated analog outputs to source bias voltages to your device under test, to control your analog programmable power supplies, or use the outputs as setpoints for your control systems. The outputs are programmed directly in volts, either from the front panel or from the bus.
Key Features & Specifications:
– 16 bits of digital input and output
– 100 kHz totalizer input
– Two +/-12V analog outputs -
Module
HP-Agilent/Keysight N6731B
Keysight basic modules provide stable output, device protection, and accurate measurements. A single range allows programming voltages and currents from 0 V and 0 A to their maximum voltage and current rating. Use 2-wire local sense or 4-wire remote sense to improve regulation. All modules feature a quick disconnect connector.
Programmable output voltages: 0 to 150 V
Output power: 50 to 300 W
Voltage accuracy: 0.1% + 19 mV (5V output)
Ripple and noise 10 mV (5V output)
Up and down-programming with resistive load typically 20 msOvervoltage, overcurrent, and overtemperature protection
Basic modules are single wide allowing four per mainframe
Modules can operate at lower output power to stay within mainframe rating
Modules include a quick disconnect connector
Datasheet -
Module
HP-Agilent/Keysight 34905A
The HP 34905A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation.
The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with 2 GHz usable bandwidth, or to the BNC-to-SMB adapters provided with 1 GHz bandwidth. Multiple banks may be cascaded together for applications requiring even larger topologies– create a stubless 16:1 multiplexer in a single frame.
Key Features & Specifications:
– Dual 4 Channel RF Multiplexer
– 2 GHz bandwidth, 50 Ohm
– Cascade together for up to 16:1 multiplexer -
Module
HP-Agilent/Keysight 34906A
The HP 34906A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with 2 GHz usable bandwidth, or to the BNC-to-SMB adapters provided with 1 bandwidth. Multiple banks may be cascaded together for applications requiring even larger topologies–create a stubless 16:1 multiplexer in a single frame.
Key Features & Specifications:
– Dual 4 Channel RF Multiplexer
– 2 GHz bandwidth, 75 Ohm
– Cascade together for up to 16:1 multiplexer
– BNC to SMB adapter cables included
-
Module
AGILENT 34903A – 20 Channel Actuator/GP Switch Module for 34970A/34972A
The Agilent 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
* 20 Channel Actuator/GP Switch
* SPDT (Form C) latching relays
* 300 V, 1 A actuation and control -
Module
AGILENT 34907A Multifunction Module for 34970A/34972A
The HP 34907A module for the 34970A/34972A Data Acquisition/Switch Unit allows great flexibility for a variety of sense and control applications. It combines two 8-bit ports of digital input and output, a 100 kHz gated totalizer, and two ±12V analog outputs – all on a single earth-referenced module. The digital inputs and totalizer input may be included in a scan. Alarm limits for the digital and event counter inputs are evaluated continuously, capturing and logging alarm conditions even between scans.
Use the digital outputs with an external power supply to control microwave switches and attenuators, solenoids, power relays, indicators, and more. Use the digital inputs to sense limit switch and digital bus status. There are no complex handshake modes; reads and writes are initiated either from the front panel or the bus.
Count events from devices like photo interrupters, limit switches, and Hall-effect sensors.
It keeps an updated total which can be read via the front panel or programmatically at any time. With 26 bits of resolution, it can count events at full speed for nearly 45 minutes without an overflow.
Use the two electronically calibrated analog outputs to source bias voltages to your device under test, to control your analog programmable power supplies, or use the outputs as setpoints for your control systems. The outputs are programmed directly in volts, either from the front panel or from the bus.
Key Features & Specifications:
– 16 bits of digital input and output
– 100 kHz totalizer input
– Two +/-12V analog outputs -
Module
HP-Agilent/Keysight N6731B
Keysight basic modules provide stable output, device protection, and accurate measurements. A single range allows programming voltages and currents from 0 V and 0 A to their maximum voltage and current rating. Use 2-wire local sense or 4-wire remote sense to improve regulation. All modules feature a quick disconnect connector.
Programmable output voltages: 0 to 150 V
Output power: 50 to 300 W
Voltage accuracy: 0.1% + 19 mV (5V output)
Ripple and noise 10 mV (5V output)
Up and down-programming with resistive load typically 20 msOvervoltage, overcurrent, and overtemperature protection
Basic modules are single wide allowing four per mainframe
Modules can operate at lower output power to stay within mainframe rating
Modules include a quick disconnect connector
Datasheet -
Module
HP-Agilent/Keysight 34905A
The HP 34905A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation.
The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with 2 GHz usable bandwidth, or to the BNC-to-SMB adapters provided with 1 GHz bandwidth. Multiple banks may be cascaded together for applications requiring even larger topologies– create a stubless 16:1 multiplexer in a single frame.
Key Features & Specifications:
– Dual 4 Channel RF Multiplexer
– 2 GHz bandwidth, 50 Ohm
– Cascade together for up to 16:1 multiplexer -
Module
HP-Agilent/Keysight 34906A
The HP 34906A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with 2 GHz usable bandwidth, or to the BNC-to-SMB adapters provided with 1 bandwidth. Multiple banks may be cascaded together for applications requiring even larger topologies–create a stubless 16:1 multiplexer in a single frame.
Key Features & Specifications:
– Dual 4 Channel RF Multiplexer
– 2 GHz bandwidth, 75 Ohm
– Cascade together for up to 16:1 multiplexer
– BNC to SMB adapter cables included