ItalianoPower Supply
Showing 61–90 of 97 results
-
Power Supply
METAF HPS3010D
Metaf HPS3010D is a Single-channel direct current (0 – 10 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
DatasheetSKU: n/a€140.00 View Product -
Power Supply
METAF HPS305D
Metaf HPS305D is a Single-channel direct current (0 – 5 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
DatasheetSKU: n/a€130.00 View Product -
Power Supply
METAF HPS605D
Metaf HPS605D is a Single-channel direct current (0 – 5 A) and voltage (0 – 60 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
DatasheetSKU: n/a€150.00 View Product -
Power Supply
RIGOL DP2031
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 5 A, DC, max 222 W). 4.3-inch LCD color touch screen. High resolution for measurement of 1 μA low range current. Low output ripple and noise <350 μVrms/2 mVpp. USB HOST, LAN, Digital I/O, and RS232 (standard)
3 electrically isolated independent channels with a maximum total power of up to 222 W
32 V/3 A || 32 V/3 A || 6 V/5 A (standard)
32 V/2 A || 32 V/2 A || 6 V/10 A (optional)
4.3-inch LCD color touch screen
Internal series/parallel connections for CH1 and CH2
High resolution for measurement of 1 μA low range current
Capability to measure and display wide dynamic ranges of current
Excellent programming/readback accuracy
Transient response time <50 μs
Front and rear output terminals
2-wire or 4-wire remote sense
A maximum of 512 arbitrary points with dwell time down to 1 ms; various built-in basic waveforms
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Automatic switchover between low and high range measurement
Timing output, energy consumption analysis (IoT), data logging and analysis
Capability to measure the minimum of 1 ms pulse current
Three rack-units (3U), 1/2-rack form factor
Software control
Over voltage, over current, and over temperature protection
Various interfaces available: USB HOST, LAN, Digital I/O, and RS232 (standard)SKU: n/a€1,099.00 View Product -
Power Supply
Rigol DP711
The Rigol DP711 is a very high quality programmable laboratory power supply with one DC output (30 V/5 A) and a maximum power output of 150 W. Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves.
The menu has an intuitive structure. The Rigol DP711 features a relative large (8.9 cm / 3.5″) and easy to read TFT display.
A timer control can be used to set the output signal to different values in up to 2048 groups.SKU: 1032€295.00 View Product -
Power Supply
Rigol DP712
The Rigol DP712 is a very high quality programmable laboratory power supply with one DC output (50 V/3 A) and a maximum power output of 150 W. Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves.
The menu has an intuitive structure. The Rigol DP712 features a relative large (8.9 cm / 3.5″) and easy to read TFT display.
A timer control can be used to set the output signal to different values in up to 2048 groups.SKU: 1033€295.00 View Product -
Power Supply
Rigol DP811
The Rigol DP811 is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 924€549.00 View Product -
Power Supply
Rigol DP811A
The Rigol DP811A is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 738€670.00 View Product -
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
SKU: n/a€589.00 View Product -
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
DatasheetSKU: n/a€710.00 View Product -
Power Supply
RIGOL DP821
The Rigol DP821 is a very high quality programmable laboratory power supply with two switchable outputs (60 V/1 A and 8 V/10 A) and a maximum power output of 140 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP821 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 923€549.00 View Product -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions.SKU: n/a€599.00 View Product -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
DatasheetSKU: n/a€729.00 View Product -
Power Supply
Rigol DP831
The Rigol DP831 is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 922€419.00 View Product -
Power Supply
RIGOL DP831A
The Rigol DP831A is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
DatascheetSKU: 441€590.00 View Product
-
Power Supply
METAF HPS3010D
Metaf HPS3010D is a Single-channel direct current (0 – 10 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet -
Power Supply
METAF HPS305D
Metaf HPS305D is a Single-channel direct current (0 – 5 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet -
Power Supply
METAF HPS605D
Metaf HPS605D is a Single-channel direct current (0 – 5 A) and voltage (0 – 60 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet -
Power Supply
RIGOL DP2031
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 5 A, DC, max 222 W). 4.3-inch LCD color touch screen. High resolution for measurement of 1 μA low range current. Low output ripple and noise <350 μVrms/2 mVpp. USB HOST, LAN, Digital I/O, and RS232 (standard)
3 electrically isolated independent channels with a maximum total power of up to 222 W
32 V/3 A || 32 V/3 A || 6 V/5 A (standard)
32 V/2 A || 32 V/2 A || 6 V/10 A (optional)
4.3-inch LCD color touch screen
Internal series/parallel connections for CH1 and CH2
High resolution for measurement of 1 μA low range current
Capability to measure and display wide dynamic ranges of current
Excellent programming/readback accuracy
Transient response time <50 μs
Front and rear output terminals
2-wire or 4-wire remote sense
A maximum of 512 arbitrary points with dwell time down to 1 ms; various built-in basic waveforms
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Automatic switchover between low and high range measurement
Timing output, energy consumption analysis (IoT), data logging and analysis
Capability to measure the minimum of 1 ms pulse current
Three rack-units (3U), 1/2-rack form factor
Software control
Over voltage, over current, and over temperature protection
Various interfaces available: USB HOST, LAN, Digital I/O, and RS232 (standard) -
Power Supply
Rigol DP711
The Rigol DP711 is a very high quality programmable laboratory power supply with one DC output (30 V/5 A) and a maximum power output of 150 W. Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves.
The menu has an intuitive structure. The Rigol DP711 features a relative large (8.9 cm / 3.5″) and easy to read TFT display.
A timer control can be used to set the output signal to different values in up to 2048 groups. -
Power Supply
Rigol DP712
The Rigol DP712 is a very high quality programmable laboratory power supply with one DC output (50 V/3 A) and a maximum power output of 150 W. Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves.
The menu has an intuitive structure. The Rigol DP712 features a relative large (8.9 cm / 3.5″) and easy to read TFT display.
A timer control can be used to set the output signal to different values in up to 2048 groups. -
Power Supply
Rigol DP811
The Rigol DP811 is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply
Rigol DP811A
The Rigol DP811A is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
-
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
Datasheet -
Power Supply
RIGOL DP821
The Rigol DP821 is a very high quality programmable laboratory power supply with two switchable outputs (60 V/1 A and 8 V/10 A) and a maximum power output of 140 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP821 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions. -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
Datasheet -
Power Supply
Rigol DP831
The Rigol DP831 is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet -
Power Supply
RIGOL DP831A
The Rigol DP831A is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet
-
Power Supply
METAF HPS3010D
Metaf HPS3010D is a Single-channel direct current (0 – 10 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet€140.00 View Product -
Power Supply
METAF HPS305D
Metaf HPS305D is a Single-channel direct current (0 – 5 A) and voltage (0 – 30 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet€130.00 View Product -
Power Supply
METAF HPS605D
Metaf HPS605D is a Single-channel direct current (0 – 5 A) and voltage (0 – 60 V) power supply unit with built-in LED display.
Features:
* Single-channel output.
* CC/CV auto switchable.
* 110V/220V switchable.
* Overload protection function.
* Overheat protection function.
* Short circuit protection function.
* Coarse/fine adjustment of voltage and current.
* Cooling with fan.
* 3/4 digital LED display for voltage and current.
Datasheet€150.00 View Product -
Power Supply
RIGOL DP2031
DC power supply with 3 independent output channels (+32 V / 3 A, +32 V / 3 A, +6 V / 5 A, DC, max 222 W). 4.3-inch LCD color touch screen. High resolution for measurement of 1 μA low range current. Low output ripple and noise <350 μVrms/2 mVpp. USB HOST, LAN, Digital I/O, and RS232 (standard)
3 electrically isolated independent channels with a maximum total power of up to 222 W
32 V/3 A || 32 V/3 A || 6 V/5 A (standard)
32 V/2 A || 32 V/2 A || 6 V/10 A (optional)
4.3-inch LCD color touch screen
Internal series/parallel connections for CH1 and CH2
High resolution for measurement of 1 μA low range current
Capability to measure and display wide dynamic ranges of current
Excellent programming/readback accuracy
Transient response time <50 μs
Front and rear output terminals
2-wire or 4-wire remote sense
A maximum of 512 arbitrary points with dwell time down to 1 ms; various built-in basic waveforms
Low output ripple and noise <350 μVrms/2 mVpp
Command processing time <10 ms
Automatic switchover between low and high range measurement
Timing output, energy consumption analysis (IoT), data logging and analysis
Capability to measure the minimum of 1 ms pulse current
Three rack-units (3U), 1/2-rack form factor
Software control
Over voltage, over current, and over temperature protection
Various interfaces available: USB HOST, LAN, Digital I/O, and RS232 (standard)€1,099.00 View Product -
Power Supply
Rigol DP711
The Rigol DP711 is a very high quality programmable laboratory power supply with one DC output (30 V/5 A) and a maximum power output of 150 W. Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves.
The menu has an intuitive structure. The Rigol DP711 features a relative large (8.9 cm / 3.5″) and easy to read TFT display.
A timer control can be used to set the output signal to different values in up to 2048 groups.€295.00 View Product -
Power Supply
Rigol DP712
The Rigol DP712 is a very high quality programmable laboratory power supply with one DC output (50 V/3 A) and a maximum power output of 150 W. Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves.
The menu has an intuitive structure. The Rigol DP712 features a relative large (8.9 cm / 3.5″) and easy to read TFT display.
A timer control can be used to set the output signal to different values in up to 2048 groups.€295.00 View Product -
Power Supply
Rigol DP811
The Rigol DP811 is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€549.00 View Product -
Power Supply
Rigol DP811A
The Rigol DP811A is a very high quality programmable laboratory power supply with a switchable output (20 V/10 A or 40 V/5 A) and a maximum power output of 200 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP811A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€670.00 View Product -
Power Supply, Programmable DC Electronic Loa
RIGOL DP813
The Rigol DP813 belongs to the Rigol DP800 series and has 1 channel. The power supply has two ranges that can be used on the single channel, 0-8V/0-20A and 0-20V/0-10A. The lab power supply has USB Host, USB Device interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 200W. The lab power supplies are equipped with a clear display where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
€589.00 View Product -
Power Supply
RIGOL DP813A
Technical specifications:
– Excellent linear regulation and load regulation ratio
– Fast transient response time: <50us
– Standard OVP / OCP / OTP protection functions
– Standard timing output
– Integrated V, A, W measurements and waveform display
– Independent control for each channel
– 3.5 inch TFT displayDifferences between + A and Non-A models:
– Support for more advanced functions: timer and delay output (are standard for all models), while recorder / analyzer / monitor / trigger functions (are standard for “+ A” models and optional for other models)
– Support of various interfaces: USB Host & Device (standard for all models), USB-GPIB (optional for all models), LAN / RS232 / Digital IO (standard for “+ A” models and optional for other models)
– The + A and Non-A models also differ in the values of some specifications, refer to the values shown in the datasheet.
Datasheet€710.00 View Product -
Power Supply
RIGOL DP821
The Rigol DP821 is a very high quality programmable laboratory power supply with two switchable outputs (60 V/1 A and 8 V/10 A) and a maximum power output of 140 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP821 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€549.00 View Product -
Power Supply
RIGOL DP822
DC power supply with 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
DP822A/DP822: 2 outputs, 20V/5A || 5V/16A, with remote Sense, total power up to 180W
Low ripple and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
Excellent linear regulation rate and load regulation rate
Fast transient response time: <50μs
Some channels are isolated
Standard OVP/OCP/OTP protection functions
Standard timing output
Built-in V,A,W measurements and waveform display
Independent control for each channel
Support more advanced functions: timer and delay output(standard),
recorder/analyzer/monitor/trigger(standard for “+A” models and optional for other models)
5-inch TFT display
Various interfaces: USB Host&Device(standard), USB-GPIB (optional),
LAN/RS232/Digital IO(standard for “+A” models and optional for other models)
For DP822, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions.€599.00 View Product -
Power Supply
RIGOL DP822A
The Rigol DP822A has 2 channels, the first channel can supply a voltage of 0-20V and a current of 0-5A. The second channel can provide a voltage of 0-5V and a current of 0-16A. The lab power supply has USB Host/USB
Device, LAN, RS232 and Digital I/O interfaces. These Rigol lab power supplies are good value for money. They are very accurate and have a power up to 180W. The lab power supplies are equipped with a clear display
where the built-in voltage, current and power measurements are displayed. The power supplies can also be programmed with the supplied software using a PC.
Key Features & Specifications:
–Low Ripple Noise: <350uvrms / 2mvpp
–Fast Transient Response Time: < 50us
–Standard Timing Output
–Built in V / A / W Measurement and Waveform Display
–Output Analysis, Monitoring, Setting Preset and Other Functions
–Original 3.5-inch Tft Wide Screen Display
Datasheet€729.00 View Product -
Power Supply
Rigol DP831
The Rigol DP831 is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831 features a relative large (8.9 cm / 3.5″) and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€419.00 View Product -
Power Supply
RIGOL DP831A
The Rigol DP831A is a very high quality programmable laboratory power supply with three switchable outputs (+8 V/5 A, +30 V/2 A and -30 V/2 A) and a maximum power output of 160 W.
Like all Rigol devices, the power supply features a very well constructed and easy to use interface, which also offers comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.
The Rigol DP831A features a relative large (8.9 cm / 3.5″) and easy to read TFT color display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.
Datascheet€590.00 View Product