ItalianoShop
Showing 31–60 of 1498 results
-
Power & Harmonic Analyzer
ELCONTROL NANOVIP PLUS
The NANOVIP PLUS is a truly portable electrical energy analyzer for balanced single-phase and three-phase systems.
The NANOVIP PLUS can measure more than 100 key parameters and display them on a large, high-contrast LCD display.
Measurements also include Harmonic Analysis from 1 to 24 and DC measurements (using a DC clamp).
The high-speed serial port and dedicated NANOWIN software add further power to the Nanovip Plus, allowing for complete graphical display and analysis of measurement data, both as real-time measurements and by transferring measurement data to a PC’s hard drive.
Extreme portability, excellent performance—not only in terms of available functions, but above all in terms of accuracy and reliability—
– best price/performance ratio: the Nanovip
Plus should be in every electrical installer’s toolkit!SKU: n/a -
Amplifier
AMPLIFIER RESEARCH 25W1000M7
Broadband Power Amplifier 100MHz – 1GHz, 25W
The Amplifier Research 25W1000M7 is a broadband, solid-state amplifier rated from 100 to 1000 MHz, CW linear power is 20 watts minimum.
It features instantaneous bandwidth, flat response, and immunity from even the worst case mismatch including shorted or open cables without damage or system shutdown.
Frequency range: 100 MHz to 1 GHz
Power output: 25 W
SKU: n/a -
Probe Offset Control and Power Module
HP-Agilent/Keysight 1143A
Keysight’s 1143A probe offset control and power module provides power and independent offset control for the Keysight 54700 Series probes. The probe’s offset is controllable via a nine-pin, D-subminiature connector on the rear panel. The ±50 V offset capability extends the dynamic range of the probe measurement system beyond that of many test and measurement instruments.
The Keysight 54701A active probe with the 1143A probe offset control and power module is versatile to use with any test and measurement equipment with a 50 ohm input.
programmable offset
±50 V offset
number of independently operated probes: 2
positive power output: +17.3 V ±150 mV
negative power output: -17.3 V ±150 mV
maximum current capability (both +17.3 V and -17.3 V supply): 300 mA
offset current: Variable from zero to ±5 mA
operating temperature: 0 to 55°C
operating humitity: 95% relative humidity at 40°C
net weight: 1.5 kg (3.4 lbs.)
shipping weight: 2.4 kg (5.4 lbs)
power requirements: 90 to 132 / 198 to 264 Vac, 47 to 440 Hz, 40 VA maximum
Dimensions: 211 mm (W) x 173 mm (D) x 78 mm (H) (8.3 x 6.8 x 3.1 inches)SKU: n/a -
Pulse Generator
WAVETEK 801
The Wavewek Model 801 is a 50 MHz general purpose laboratory pulse generator. The instrument gives you full control in primary pulse triggering and shaping plus simultaneous TTL, ECL, ECLand sync pulses. The primary pulse output has controllability in offset and independent rise/fall durations, as well as pulse width, pulse delay and a choice of positive, negative or complementary outputs. The TTL, ECL and ECLare of fixed levels and rise times that are standard for use with compatible devices. The primary pulse has minimum rise and fall times of 7 ns and a maximum of 250 ms.
The output is ± 20 volts with 50 ohms source impedance which provides ± 10 volts into a 50 ohms load. Upper and lower pulse levels are fully adjustable through ± 20 volts.
External triggering can be set to any point of the rising or trailing edge of the trigger signal. Single pulses or pulse pairs may be triggered; pulse width may be trigger controlled; continuous pulses may be gated and a precise number of pulses may be triggered for a ‘burst’ output. Manual and external triggering is indicated by an LED on the front panel for rapid visual set of trigger level.
SKU: n/a -
Signal Generator
ROHDE & SCHWARZ SMY01
Signal generators of the Rohde & Schwarz SMY family from Rohde&Schwarz are cost-effective instruments for testing AM, FM and jM receivers as well as for component measurements.
Designed exclusively for the main applications of signal generators by cutting out the unnecessaries, R&S SMY features an outstanding price/performance ratio. Thanks to its comprehensive basic features and excellent signal characteristics, it is an economical solution for universal use in lab, production and servicing environments.
Level range -140 dBm to +13 dBm (19 dBm overrange) , sufficient even for receivers of highest sensitivity
High level accuracy and low RF leakage allowing accurate and undegraded sensitivity measurements
FM-DC with high accuracy of carrier frequency for testing pagers and receivers fitted with digital squelches
Low SSB phase noise( -114 dBc/Hz) and high spurious rejection for all in-channel and blocking measurements
Low residual FM affording ample of margin for S/N measurements
Modulation generator 1 Hz to 500 kHz for modulation frequency response measurements
Stereo channel separation of 50 dB and low harmonic distortion for testing FM stereo receivers
Non-interrupting level setting over a range of 20 dB for reproducible measurement of squelch hysteresis
Frequency resolution 1 Hz, suitable also for narrowband test items
FM-DC, deviation up to 20 MHz for VCO simulation
FM bandwidth 2 MHz for fast FSK and telemetry applications
High output level up to 19 dBm (25 dBm with option R&S SMY-B40) for component and overdrive testing
AF synthesizer 1 Hz to 500 kHz, separate use as AF signal source for external applications possible, eg recording of AF frequency response
Remote-control interface IEC625/IEEE488 for use in automatic test systems
RF sweep
Sequence function and SEQ input for semi-automatic useSKU: n/a -
Dual Regulated Power Supply
ELIND 32DP32
Dual Regulated Power Supply with 2x 32 V and 2x 3,2 A. These units are made of 2 pieces of 3232D assembled in a single case with one power cord and one line switch. Output V/I : 0 – 32 V (CV) and 0 – 3,2 A (CC) Line regulation : 0,005% ± 0,5 mV and 0,1% ± 50 µA Load regulation : 0,01% ± 1 mV and 0,02% ± 100 µA Ripple (RMS) : 100 µV, 250 µA
SKU: n/a -
SYSTEM VOLTMETER
HP-Agilent/Keysight 3437A
SYSTEM VOLTMETER OPT.030
System Voltmeter is a microprocessor controlled 3 1/2-digit successive approximation System Voltmeter. It offers three DC floating input ranges: 0.1 V (0.06% + 2.2-digits), 1.0 V (0.03% + 2-digits), and 10.0 V (0.05 + 2-digits) full scale. The trigger delay can be set from 0.1 Micros to 1.0 second and the number of readings can be set from 0 to 9999 readings. Also provides external trigger capabilities which can be delayed from 0 to 1 Sec in 100 nS steps. The 3437A will provide years of dependable service. It's easy to use and can be programmed from the front-panel or HP-IB interface.
SKU: n/a -
Signal Generator
HP-Agilent/Keysight 8648B
SIGNAL GENERATOR 100KHZ – 2000MHZ OPT.1E6
The HP/Agilent 8648B is a Synthesized RF Signal Generator with frequency range from 9 kHz to 2000 MHz The unit starts with the basic capabilities of the Agilent HP 8647A, enhances residual FM, level accuracy and phase noise performance, offers optional pulse modulation and high power, and extends the frequency to 2 GHz.
SKU: n/a -
Two-Line V Network
ROHDE & SCHWARZ ESH3-Z5
The Rohde & Schwarz ESH3-Z5 is a 50 µH two-line V-network Artificial Mains Network (AMN) fitted with UK mains 13 A plug and socket connections for use on AC power supplies. It is placed between supply and the equipment under test in order to accurately measure the interference that the equipment is emitting at its supply input.
The unit comes complete with 50 Ω loads to terminate the monitor ports.
The performance characteristics of this item comply with the following standards:
CISPR 16-1-2 / BS EN 55016-1-2 (50 µH requirements)
CISPR 25 / BS EN 55025 (for AC Supplies)
EN 61000
Mil Std 461General specification
Frequency Range: 9 kHz to 30 MHz
Impedance Accuracy: ± 20%
Maximum Current: 10 A
Maximum Voltage: 250 Vrms
Max Input Frequency: 63 Hz
Power Connectors: 13 A plug & socket
RF Connector: BNC (f)SKU: n/a -
Signal Generator
HP-Agilent/Keysight 8647A
Economical synthesized signal generator
Electronic attenuator
Wide frequency and power coverage
Remote and memory interfaces for semi-automated testing
Simple, dependable operationIdeal for manufacturing high-volume products such as cordless telephones, pagers and two-way radios, the Keysight 8647A Synthesized RF Signal Generator delivers essential performance and reliability at an affordable price. Designed for semi-automated receiver test, and a variety of general purpose applications, the Keysight 8647A meets stringent quality standards and promotes measurement consistency and repeatability. For example, the all-electronic attenuator, with no moving parts, easily handles millions of amplitude cycles with highly repeatable results. In addition, the simplistic design of the front panel shortens the operator’s learning curve and increases productivity. With 300 storage registers and ten user-definable sequences (accessible from a remote keypad), the Keysight 8647A easily adapts to any test procedure.
SKU: n/a -
Programmable DC Electronic Loa
CHROMA 63803
The Chroma 63803 Load can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents over-stressing thereby giving reliable and unbiased test results.
Specifications:Single
3.6 kW
350 V
36 APower Rating: 3600W
Voltage Range: 50V to 350Vrms
Current Range: Up to 18Arms, 36Arms, 45Arms
Peak Current: Up to 54A, 108A, 135A
Parallel / 3-Phase Function
Frequency Range: 45 to 440Hz, DC
Crest Factor Range: 1.414 to 5.0
Power Factor Range: 0 to 1 lead or lag (Rectified mode)
CC, CR, CV, CP for DC Loading
Constant & Rectified Load Modes for AC Loading
Analog Voltage & Current Monitor
Timing Measurement for Battery, UPS, Fuse and Breaker tests
Measurement: V, I, PF, CF, P, Q, S, F, R, Ip+/- and THDv
Short circuit simulation
Full Protection: OC, OP, OT protection and OV alarm
GPIB & RS-232 includedSKU: n/a -
Switch/Control Unit
HP-Agilent/Keysight 3488A
The Agilent HP3488A provides signal switching with the integrity and isolation needed for high-performance production test systems. It also offers a flexible, low-cost interconnection for automating experiments on the bench and for developing tests in the lab.
Additional Features:
DC to 26.5 GHz signal switching
Up to 50 channels
Matrix, multiplexer, and general purpose relays
40 configuration storage registers
Digital I/O control and actuation
11 switch and control modulesSKU: n/a -
Differential Probes
AGILENT-HP/Keysight 1141A
The Keysight 1141A is a 1X FET differential probe with 200 MHz bandwidth and 3000:1 CMRR (Common Mode Rejection Ratio) at 1 MHz. The probe has an input resistance of 1 MΩ and low input capacitance of 7 pF, to minimize circuit loading.
The Keysight 1141A 200 MHz Differential Probe must be used with the Keysight 1142A Probe Control and Power Module. It can be connected to any instrument with 50 ohm inputs. An external 50 ohm termination can also be used with high impedance inputs.SKU: n/a -
Current Probe
SIGLENT CP4050
The Siglent CP4050 is a high-performance current probe designed for accurate and reliable measurement of AC and DC currents. With a wide bandwidth of up to 1 MHz and a peak current measurement capability of 140 A, this probe is ideal for various industrial and engineering applications. Its precision and versatility make it a valuable tool for professionals in power electronics, motor drives, and circuit design.
SKU: n/a -
Precision DC Power Module
AGILENT-HP/Keysight N6732B
The Keysight N6732B 50 W basic DC power module provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power your DUT or ATE system resources, such as fixture control.
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance come standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 – 500 W.
Download BenchVue Basic app for free to control your instruments.
Output RatingsVoltage: 8 V
Current: 6.25 A
Power: 50 WProgramming Accuracy (at 23°C ±5°)
Voltage: 0.1% + 19 mV
Current: 0.15% + 20 mARipple and Noise (20 Hz to 20 MHz)
Voltage rms: 2 mV
Voltage peak-to-peak: 12 mV
Current rms: 4 mASKU: n/a
-
Power & Harmonic Analyzer
ELCONTROL NANOVIP PLUS
The NANOVIP PLUS is a truly portable electrical energy analyzer for balanced single-phase and three-phase systems.
The NANOVIP PLUS can measure more than 100 key parameters and display them on a large, high-contrast LCD display.
Measurements also include Harmonic Analysis from 1 to 24 and DC measurements (using a DC clamp).
The high-speed serial port and dedicated NANOWIN software add further power to the Nanovip Plus, allowing for complete graphical display and analysis of measurement data, both as real-time measurements and by transferring measurement data to a PC’s hard drive.
Extreme portability, excellent performance—not only in terms of available functions, but above all in terms of accuracy and reliability—
– best price/performance ratio: the Nanovip
Plus should be in every electrical installer’s toolkit! -
Amplifier
AMPLIFIER RESEARCH 25W1000M7
Broadband Power Amplifier 100MHz – 1GHz, 25W
The Amplifier Research 25W1000M7 is a broadband, solid-state amplifier rated from 100 to 1000 MHz, CW linear power is 20 watts minimum.
It features instantaneous bandwidth, flat response, and immunity from even the worst case mismatch including shorted or open cables without damage or system shutdown.
Frequency range: 100 MHz to 1 GHz
Power output: 25 W
-
Probe Offset Control and Power Module
HP-Agilent/Keysight 1143A
Keysight’s 1143A probe offset control and power module provides power and independent offset control for the Keysight 54700 Series probes. The probe’s offset is controllable via a nine-pin, D-subminiature connector on the rear panel. The ±50 V offset capability extends the dynamic range of the probe measurement system beyond that of many test and measurement instruments.
The Keysight 54701A active probe with the 1143A probe offset control and power module is versatile to use with any test and measurement equipment with a 50 ohm input.
programmable offset
±50 V offset
number of independently operated probes: 2
positive power output: +17.3 V ±150 mV
negative power output: -17.3 V ±150 mV
maximum current capability (both +17.3 V and -17.3 V supply): 300 mA
offset current: Variable from zero to ±5 mA
operating temperature: 0 to 55°C
operating humitity: 95% relative humidity at 40°C
net weight: 1.5 kg (3.4 lbs.)
shipping weight: 2.4 kg (5.4 lbs)
power requirements: 90 to 132 / 198 to 264 Vac, 47 to 440 Hz, 40 VA maximum
Dimensions: 211 mm (W) x 173 mm (D) x 78 mm (H) (8.3 x 6.8 x 3.1 inches) -
Pulse Generator
WAVETEK 801
The Wavewek Model 801 is a 50 MHz general purpose laboratory pulse generator. The instrument gives you full control in primary pulse triggering and shaping plus simultaneous TTL, ECL, ECLand sync pulses. The primary pulse output has controllability in offset and independent rise/fall durations, as well as pulse width, pulse delay and a choice of positive, negative or complementary outputs. The TTL, ECL and ECLare of fixed levels and rise times that are standard for use with compatible devices. The primary pulse has minimum rise and fall times of 7 ns and a maximum of 250 ms.
The output is ± 20 volts with 50 ohms source impedance which provides ± 10 volts into a 50 ohms load. Upper and lower pulse levels are fully adjustable through ± 20 volts.
External triggering can be set to any point of the rising or trailing edge of the trigger signal. Single pulses or pulse pairs may be triggered; pulse width may be trigger controlled; continuous pulses may be gated and a precise number of pulses may be triggered for a ‘burst’ output. Manual and external triggering is indicated by an LED on the front panel for rapid visual set of trigger level.
-
Signal Generator
ROHDE & SCHWARZ SMY01
Signal generators of the Rohde & Schwarz SMY family from Rohde&Schwarz are cost-effective instruments for testing AM, FM and jM receivers as well as for component measurements.
Designed exclusively for the main applications of signal generators by cutting out the unnecessaries, R&S SMY features an outstanding price/performance ratio. Thanks to its comprehensive basic features and excellent signal characteristics, it is an economical solution for universal use in lab, production and servicing environments.
Level range -140 dBm to +13 dBm (19 dBm overrange) , sufficient even for receivers of highest sensitivity
High level accuracy and low RF leakage allowing accurate and undegraded sensitivity measurements
FM-DC with high accuracy of carrier frequency for testing pagers and receivers fitted with digital squelches
Low SSB phase noise( -114 dBc/Hz) and high spurious rejection for all in-channel and blocking measurements
Low residual FM affording ample of margin for S/N measurements
Modulation generator 1 Hz to 500 kHz for modulation frequency response measurements
Stereo channel separation of 50 dB and low harmonic distortion for testing FM stereo receivers
Non-interrupting level setting over a range of 20 dB for reproducible measurement of squelch hysteresis
Frequency resolution 1 Hz, suitable also for narrowband test items
FM-DC, deviation up to 20 MHz for VCO simulation
FM bandwidth 2 MHz for fast FSK and telemetry applications
High output level up to 19 dBm (25 dBm with option R&S SMY-B40) for component and overdrive testing
AF synthesizer 1 Hz to 500 kHz, separate use as AF signal source for external applications possible, eg recording of AF frequency response
Remote-control interface IEC625/IEEE488 for use in automatic test systems
RF sweep
Sequence function and SEQ input for semi-automatic use -
Dual Regulated Power Supply
ELIND 32DP32
Dual Regulated Power Supply with 2x 32 V and 2x 3,2 A. These units are made of 2 pieces of 3232D assembled in a single case with one power cord and one line switch. Output V/I : 0 – 32 V (CV) and 0 – 3,2 A (CC) Line regulation : 0,005% ± 0,5 mV and 0,1% ± 50 µA Load regulation : 0,01% ± 1 mV and 0,02% ± 100 µA Ripple (RMS) : 100 µV, 250 µA
-
SYSTEM VOLTMETER
HP-Agilent/Keysight 3437A
SYSTEM VOLTMETER OPT.030
System Voltmeter is a microprocessor controlled 3 1/2-digit successive approximation System Voltmeter. It offers three DC floating input ranges: 0.1 V (0.06% + 2.2-digits), 1.0 V (0.03% + 2-digits), and 10.0 V (0.05 + 2-digits) full scale. The trigger delay can be set from 0.1 Micros to 1.0 second and the number of readings can be set from 0 to 9999 readings. Also provides external trigger capabilities which can be delayed from 0 to 1 Sec in 100 nS steps. The 3437A will provide years of dependable service. It's easy to use and can be programmed from the front-panel or HP-IB interface.
-
Signal Generator
HP-Agilent/Keysight 8648B
SIGNAL GENERATOR 100KHZ – 2000MHZ OPT.1E6
The HP/Agilent 8648B is a Synthesized RF Signal Generator with frequency range from 9 kHz to 2000 MHz The unit starts with the basic capabilities of the Agilent HP 8647A, enhances residual FM, level accuracy and phase noise performance, offers optional pulse modulation and high power, and extends the frequency to 2 GHz.
-
Two-Line V Network
ROHDE & SCHWARZ ESH3-Z5
The Rohde & Schwarz ESH3-Z5 is a 50 µH two-line V-network Artificial Mains Network (AMN) fitted with UK mains 13 A plug and socket connections for use on AC power supplies. It is placed between supply and the equipment under test in order to accurately measure the interference that the equipment is emitting at its supply input.
The unit comes complete with 50 Ω loads to terminate the monitor ports.
The performance characteristics of this item comply with the following standards:
CISPR 16-1-2 / BS EN 55016-1-2 (50 µH requirements)
CISPR 25 / BS EN 55025 (for AC Supplies)
EN 61000
Mil Std 461General specification
Frequency Range: 9 kHz to 30 MHz
Impedance Accuracy: ± 20%
Maximum Current: 10 A
Maximum Voltage: 250 Vrms
Max Input Frequency: 63 Hz
Power Connectors: 13 A plug & socket
RF Connector: BNC (f) -
Signal Generator
HP-Agilent/Keysight 8647A
Economical synthesized signal generator
Electronic attenuator
Wide frequency and power coverage
Remote and memory interfaces for semi-automated testing
Simple, dependable operationIdeal for manufacturing high-volume products such as cordless telephones, pagers and two-way radios, the Keysight 8647A Synthesized RF Signal Generator delivers essential performance and reliability at an affordable price. Designed for semi-automated receiver test, and a variety of general purpose applications, the Keysight 8647A meets stringent quality standards and promotes measurement consistency and repeatability. For example, the all-electronic attenuator, with no moving parts, easily handles millions of amplitude cycles with highly repeatable results. In addition, the simplistic design of the front panel shortens the operator’s learning curve and increases productivity. With 300 storage registers and ten user-definable sequences (accessible from a remote keypad), the Keysight 8647A easily adapts to any test procedure.
-
Programmable DC Electronic Loa
CHROMA 63803
The Chroma 63803 Load can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents over-stressing thereby giving reliable and unbiased test results.
Specifications:Single
3.6 kW
350 V
36 APower Rating: 3600W
Voltage Range: 50V to 350Vrms
Current Range: Up to 18Arms, 36Arms, 45Arms
Peak Current: Up to 54A, 108A, 135A
Parallel / 3-Phase Function
Frequency Range: 45 to 440Hz, DC
Crest Factor Range: 1.414 to 5.0
Power Factor Range: 0 to 1 lead or lag (Rectified mode)
CC, CR, CV, CP for DC Loading
Constant & Rectified Load Modes for AC Loading
Analog Voltage & Current Monitor
Timing Measurement for Battery, UPS, Fuse and Breaker tests
Measurement: V, I, PF, CF, P, Q, S, F, R, Ip+/- and THDv
Short circuit simulation
Full Protection: OC, OP, OT protection and OV alarm
GPIB & RS-232 included -
Switch/Control Unit
HP-Agilent/Keysight 3488A
The Agilent HP3488A provides signal switching with the integrity and isolation needed for high-performance production test systems. It also offers a flexible, low-cost interconnection for automating experiments on the bench and for developing tests in the lab.
Additional Features:
DC to 26.5 GHz signal switching
Up to 50 channels
Matrix, multiplexer, and general purpose relays
40 configuration storage registers
Digital I/O control and actuation
11 switch and control modules -
Differential Probes
AGILENT-HP/Keysight 1141A
The Keysight 1141A is a 1X FET differential probe with 200 MHz bandwidth and 3000:1 CMRR (Common Mode Rejection Ratio) at 1 MHz. The probe has an input resistance of 1 MΩ and low input capacitance of 7 pF, to minimize circuit loading.
The Keysight 1141A 200 MHz Differential Probe must be used with the Keysight 1142A Probe Control and Power Module. It can be connected to any instrument with 50 ohm inputs. An external 50 ohm termination can also be used with high impedance inputs. -
Current Probe
SIGLENT CP4050
The Siglent CP4050 is a high-performance current probe designed for accurate and reliable measurement of AC and DC currents. With a wide bandwidth of up to 1 MHz and a peak current measurement capability of 140 A, this probe is ideal for various industrial and engineering applications. Its precision and versatility make it a valuable tool for professionals in power electronics, motor drives, and circuit design.
-
Precision DC Power Module
AGILENT-HP/Keysight N6732B
The Keysight N6732B 50 W basic DC power module provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power your DUT or ATE system resources, such as fixture control.
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance come standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 – 500 W.
Download BenchVue Basic app for free to control your instruments.
Output RatingsVoltage: 8 V
Current: 6.25 A
Power: 50 WProgramming Accuracy (at 23°C ±5°)
Voltage: 0.1% + 19 mV
Current: 0.15% + 20 mARipple and Noise (20 Hz to 20 MHz)
Voltage rms: 2 mV
Voltage peak-to-peak: 12 mV
Current rms: 4 mA
-
Power & Harmonic Analyzer
ELCONTROL NANOVIP PLUS
The NANOVIP PLUS is a truly portable electrical energy analyzer for balanced single-phase and three-phase systems.
The NANOVIP PLUS can measure more than 100 key parameters and display them on a large, high-contrast LCD display.
Measurements also include Harmonic Analysis from 1 to 24 and DC measurements (using a DC clamp).
The high-speed serial port and dedicated NANOWIN software add further power to the Nanovip Plus, allowing for complete graphical display and analysis of measurement data, both as real-time measurements and by transferring measurement data to a PC’s hard drive.
Extreme portability, excellent performance—not only in terms of available functions, but above all in terms of accuracy and reliability—
– best price/performance ratio: the Nanovip
Plus should be in every electrical installer’s toolkit! -
Amplifier
AMPLIFIER RESEARCH 25W1000M7
Broadband Power Amplifier 100MHz – 1GHz, 25W
The Amplifier Research 25W1000M7 is a broadband, solid-state amplifier rated from 100 to 1000 MHz, CW linear power is 20 watts minimum.
It features instantaneous bandwidth, flat response, and immunity from even the worst case mismatch including shorted or open cables without damage or system shutdown.
Frequency range: 100 MHz to 1 GHz
Power output: 25 W
-
Probe Offset Control and Power Module
HP-Agilent/Keysight 1143A
Keysight’s 1143A probe offset control and power module provides power and independent offset control for the Keysight 54700 Series probes. The probe’s offset is controllable via a nine-pin, D-subminiature connector on the rear panel. The ±50 V offset capability extends the dynamic range of the probe measurement system beyond that of many test and measurement instruments.
The Keysight 54701A active probe with the 1143A probe offset control and power module is versatile to use with any test and measurement equipment with a 50 ohm input.
programmable offset
±50 V offset
number of independently operated probes: 2
positive power output: +17.3 V ±150 mV
negative power output: -17.3 V ±150 mV
maximum current capability (both +17.3 V and -17.3 V supply): 300 mA
offset current: Variable from zero to ±5 mA
operating temperature: 0 to 55°C
operating humitity: 95% relative humidity at 40°C
net weight: 1.5 kg (3.4 lbs.)
shipping weight: 2.4 kg (5.4 lbs)
power requirements: 90 to 132 / 198 to 264 Vac, 47 to 440 Hz, 40 VA maximum
Dimensions: 211 mm (W) x 173 mm (D) x 78 mm (H) (8.3 x 6.8 x 3.1 inches) -
Pulse Generator
WAVETEK 801
The Wavewek Model 801 is a 50 MHz general purpose laboratory pulse generator. The instrument gives you full control in primary pulse triggering and shaping plus simultaneous TTL, ECL, ECLand sync pulses. The primary pulse output has controllability in offset and independent rise/fall durations, as well as pulse width, pulse delay and a choice of positive, negative or complementary outputs. The TTL, ECL and ECLare of fixed levels and rise times that are standard for use with compatible devices. The primary pulse has minimum rise and fall times of 7 ns and a maximum of 250 ms.
The output is ± 20 volts with 50 ohms source impedance which provides ± 10 volts into a 50 ohms load. Upper and lower pulse levels are fully adjustable through ± 20 volts.
External triggering can be set to any point of the rising or trailing edge of the trigger signal. Single pulses or pulse pairs may be triggered; pulse width may be trigger controlled; continuous pulses may be gated and a precise number of pulses may be triggered for a ‘burst’ output. Manual and external triggering is indicated by an LED on the front panel for rapid visual set of trigger level.
-
Signal Generator
ROHDE & SCHWARZ SMY01
Signal generators of the Rohde & Schwarz SMY family from Rohde&Schwarz are cost-effective instruments for testing AM, FM and jM receivers as well as for component measurements.
Designed exclusively for the main applications of signal generators by cutting out the unnecessaries, R&S SMY features an outstanding price/performance ratio. Thanks to its comprehensive basic features and excellent signal characteristics, it is an economical solution for universal use in lab, production and servicing environments.
Level range -140 dBm to +13 dBm (19 dBm overrange) , sufficient even for receivers of highest sensitivity
High level accuracy and low RF leakage allowing accurate and undegraded sensitivity measurements
FM-DC with high accuracy of carrier frequency for testing pagers and receivers fitted with digital squelches
Low SSB phase noise( -114 dBc/Hz) and high spurious rejection for all in-channel and blocking measurements
Low residual FM affording ample of margin for S/N measurements
Modulation generator 1 Hz to 500 kHz for modulation frequency response measurements
Stereo channel separation of 50 dB and low harmonic distortion for testing FM stereo receivers
Non-interrupting level setting over a range of 20 dB for reproducible measurement of squelch hysteresis
Frequency resolution 1 Hz, suitable also for narrowband test items
FM-DC, deviation up to 20 MHz for VCO simulation
FM bandwidth 2 MHz for fast FSK and telemetry applications
High output level up to 19 dBm (25 dBm with option R&S SMY-B40) for component and overdrive testing
AF synthesizer 1 Hz to 500 kHz, separate use as AF signal source for external applications possible, eg recording of AF frequency response
Remote-control interface IEC625/IEEE488 for use in automatic test systems
RF sweep
Sequence function and SEQ input for semi-automatic use -
Dual Regulated Power Supply
ELIND 32DP32
Dual Regulated Power Supply with 2x 32 V and 2x 3,2 A. These units are made of 2 pieces of 3232D assembled in a single case with one power cord and one line switch. Output V/I : 0 – 32 V (CV) and 0 – 3,2 A (CC) Line regulation : 0,005% ± 0,5 mV and 0,1% ± 50 µA Load regulation : 0,01% ± 1 mV and 0,02% ± 100 µA Ripple (RMS) : 100 µV, 250 µA
-
SYSTEM VOLTMETER
HP-Agilent/Keysight 3437A
SYSTEM VOLTMETER OPT.030
System Voltmeter is a microprocessor controlled 3 1/2-digit successive approximation System Voltmeter. It offers three DC floating input ranges: 0.1 V (0.06% + 2.2-digits), 1.0 V (0.03% + 2-digits), and 10.0 V (0.05 + 2-digits) full scale. The trigger delay can be set from 0.1 Micros to 1.0 second and the number of readings can be set from 0 to 9999 readings. Also provides external trigger capabilities which can be delayed from 0 to 1 Sec in 100 nS steps. The 3437A will provide years of dependable service. It's easy to use and can be programmed from the front-panel or HP-IB interface.
-
Signal Generator
HP-Agilent/Keysight 8648B
SIGNAL GENERATOR 100KHZ – 2000MHZ OPT.1E6
The HP/Agilent 8648B is a Synthesized RF Signal Generator with frequency range from 9 kHz to 2000 MHz The unit starts with the basic capabilities of the Agilent HP 8647A, enhances residual FM, level accuracy and phase noise performance, offers optional pulse modulation and high power, and extends the frequency to 2 GHz.
-
Two-Line V Network
ROHDE & SCHWARZ ESH3-Z5
The Rohde & Schwarz ESH3-Z5 is a 50 µH two-line V-network Artificial Mains Network (AMN) fitted with UK mains 13 A plug and socket connections for use on AC power supplies. It is placed between supply and the equipment under test in order to accurately measure the interference that the equipment is emitting at its supply input.
The unit comes complete with 50 Ω loads to terminate the monitor ports.
The performance characteristics of this item comply with the following standards:
CISPR 16-1-2 / BS EN 55016-1-2 (50 µH requirements)
CISPR 25 / BS EN 55025 (for AC Supplies)
EN 61000
Mil Std 461General specification
Frequency Range: 9 kHz to 30 MHz
Impedance Accuracy: ± 20%
Maximum Current: 10 A
Maximum Voltage: 250 Vrms
Max Input Frequency: 63 Hz
Power Connectors: 13 A plug & socket
RF Connector: BNC (f) -
Signal Generator
HP-Agilent/Keysight 8647A
Economical synthesized signal generator
Electronic attenuator
Wide frequency and power coverage
Remote and memory interfaces for semi-automated testing
Simple, dependable operationIdeal for manufacturing high-volume products such as cordless telephones, pagers and two-way radios, the Keysight 8647A Synthesized RF Signal Generator delivers essential performance and reliability at an affordable price. Designed for semi-automated receiver test, and a variety of general purpose applications, the Keysight 8647A meets stringent quality standards and promotes measurement consistency and repeatability. For example, the all-electronic attenuator, with no moving parts, easily handles millions of amplitude cycles with highly repeatable results. In addition, the simplistic design of the front panel shortens the operator’s learning curve and increases productivity. With 300 storage registers and ten user-definable sequences (accessible from a remote keypad), the Keysight 8647A easily adapts to any test procedure.
-
Programmable DC Electronic Loa
CHROMA 63803
The Chroma 63803 Load can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents over-stressing thereby giving reliable and unbiased test results.
Specifications:Single
3.6 kW
350 V
36 APower Rating: 3600W
Voltage Range: 50V to 350Vrms
Current Range: Up to 18Arms, 36Arms, 45Arms
Peak Current: Up to 54A, 108A, 135A
Parallel / 3-Phase Function
Frequency Range: 45 to 440Hz, DC
Crest Factor Range: 1.414 to 5.0
Power Factor Range: 0 to 1 lead or lag (Rectified mode)
CC, CR, CV, CP for DC Loading
Constant & Rectified Load Modes for AC Loading
Analog Voltage & Current Monitor
Timing Measurement for Battery, UPS, Fuse and Breaker tests
Measurement: V, I, PF, CF, P, Q, S, F, R, Ip+/- and THDv
Short circuit simulation
Full Protection: OC, OP, OT protection and OV alarm
GPIB & RS-232 included -
Switch/Control Unit
HP-Agilent/Keysight 3488A
The Agilent HP3488A provides signal switching with the integrity and isolation needed for high-performance production test systems. It also offers a flexible, low-cost interconnection for automating experiments on the bench and for developing tests in the lab.
Additional Features:
DC to 26.5 GHz signal switching
Up to 50 channels
Matrix, multiplexer, and general purpose relays
40 configuration storage registers
Digital I/O control and actuation
11 switch and control modules -
Differential Probes
AGILENT-HP/Keysight 1141A
The Keysight 1141A is a 1X FET differential probe with 200 MHz bandwidth and 3000:1 CMRR (Common Mode Rejection Ratio) at 1 MHz. The probe has an input resistance of 1 MΩ and low input capacitance of 7 pF, to minimize circuit loading.
The Keysight 1141A 200 MHz Differential Probe must be used with the Keysight 1142A Probe Control and Power Module. It can be connected to any instrument with 50 ohm inputs. An external 50 ohm termination can also be used with high impedance inputs. -
Current Probe
SIGLENT CP4050
The Siglent CP4050 is a high-performance current probe designed for accurate and reliable measurement of AC and DC currents. With a wide bandwidth of up to 1 MHz and a peak current measurement capability of 140 A, this probe is ideal for various industrial and engineering applications. Its precision and versatility make it a valuable tool for professionals in power electronics, motor drives, and circuit design.
-
Precision DC Power Module
AGILENT-HP/Keysight N6732B
The Keysight N6732B 50 W basic DC power module provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power your DUT or ATE system resources, such as fixture control.
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance come standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 – 500 W.
Download BenchVue Basic app for free to control your instruments.
Output RatingsVoltage: 8 V
Current: 6.25 A
Power: 50 WProgramming Accuracy (at 23°C ±5°)
Voltage: 0.1% + 19 mV
Current: 0.15% + 20 mARipple and Noise (20 Hz to 20 MHz)
Voltage rms: 2 mV
Voltage peak-to-peak: 12 mV
Current rms: 4 mA